mypros+
Model reference

Amana YY-80-DA

Furnace

6 documents50 error codes24 service modes

Available documentation

Tech Tip

  • Instruction Sheet - 85244282 pg
    Covers this model
  • Instruction Sheet - 397971412 pg
    Covers this model

Installation Guide

  • Installation Instructions20 pg
    Covers this model
  • Installation Instructions28 pg
    Covers this model
  • Installation Instructions28 pg
    Covers this model
  • Installation Instructions7 pg
    Covers this model
MyPros+ Max

Diagnose your Amana YY-80-DA.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (50)

CodeMeaning
bFIce maker self-diagnosticsE1Ice maker self-diagnosticsE2Ice maker self-diagnosticsE3Ice maker self-diagnosticsE4Ice maker self-diagnosticsF0-E0No failureF0E0No failure present (informational code displayed when CANCEL/OFF is held for 5…F1-E0EEPROM communication error.F1-E1Upper RTD uncalibrated (internal error).F1-E2Lower RTD uncalibrated (internal error).F1-E3Fuel type (gas/electric) select failure.F1-E5Sensor usage out of range (internal error).F1-E7PCB thermistor/sensor open or shorted.F1-E9WIDE Queue full.F1E0EEPROM communications failure.F1E1EEPROM checksum failure.F1E3Fuel type (gas/electric) select failure.F1E4Microwave ACU PCBA (Appliance Control Unit Printed Circuit Board Assembly)…F2-E0Keypad disconnected.F2-E1Stuck key detected.F2-E2Stuck key detected.F2-E6CANCEL key failure.F2E0Key held down too long or shorted key.F2E1Keytail unplugged or damaged.F2E6CANCEL key failure.F3-E0Main oven temperature sensor open or shorted (upper oven).F3-E1Main oven temperature sensor open or shorted (lower oven).F3-E2BAKE/BROIL range over temperature.F3-E3CLEAN range over temperature.F3E0Oven sensor opened.
View all 50 error codes
F3E1Oven sensor shorted.F3E2BAKE/BROIL range over temperature.F3E3CLEAN range over temperature.F4E1Cavity temperature sensor failure.F4E4Humidity sensor error.F5-E0Door and latch switches do not agree during Clean mode.F5-E1Door latch not operating during Clean mode.F5-E2Latch error during CLEAN.F5E0Door switches do not agree.F5E1Door latch not operating.F5E2Latch error during clean.F6-E0Lost communications between control boards.F6-E1Over temperature condition during cook mode (runaway temp).F6-E2Over temperature condition during clean mode (runaway temp).F6-E3Over temperature condition in warming drawer (runaway temp).F8E5Exhaust air template detection failure (HF NTC thermistor issue).F9-E0Product is mis-wired.OPThermistor is open, displayed during service test thermistor readings.PAIce maker self-diagnosticsSHThermistor is shorted, displayed during service test thermistor readings.

Service modes (24)

  • 12 hour shut off disable/enablePress and hold the CLOCK key for 5 seconds.
  • 12 hour shut-offPress and hold TIMER OFF key for 5 seconds.
  • Audible signal pitch controlPress and hold DELAY START key for 5 seconds.
  • Auto Test1
  • Clear Fault Codes["Enter Diagnostic Mode by pressing CANCEL > CANCEL > START within 5 seconds.","Press TEMP/TIME '+'…
  • Cooktop lockoutPress and hold the TOP/TOP LIGHT keypad on the control panel for 5 seconds
  • damp_dry_test["Begin with a fully assembled, empty dryer with clean lint screen connected to a known good power…
  • diagnostic["Set Fabric Care/Temperature switch to AIR FLUFF","Set Signal switch to HIGH","Set Timer to TIMED…
  • Diagnostic Mode1. Plug in oven or connect power. 2. Press CANCEL > CANCEL > START within 5 seconds to enter…
  • Diagnostics Mode (Self-Diagnostic Test Mode)["Plug in microwave oven or reconnect power.","Press CANCEL button to enter standby (display shows…
  • Disable/Enable all tones (except end-of-timer and error tones)Press and hold COOK TIME key for 5 seconds.
  • Disable/Enable all tones except end-of-timer and error tonesPress and hold the COOK TIME key for 5 seconds.
  • Disable/Enable cycle and timer-end repeating tonesPress and hold TIMER SET key for 5 seconds.
  • Fahrenheit to Celsius conversionPress and hold BROIL key for 5 seconds.
  • Fault Code Viewing and Clearing1
  • Recall last failure codePress and hold the CANCEL/OFF key for 5 seconds
  • Sales demonstration modePress and hold START/ENTER key for 5 seconds.
  • Service Diagnostics Mode["On the Main (Eyebrow) UI, press and hold both temperature '-' buttons simultaneously for 3…
  • Showroom Mode["Press and hold top and bottom zone icons simultaneously for 3 seconds."]
  • Software revision numberPress and hold TIME key for 5 seconds.
  • Temperature Calibration1
  • Temperature calibration offsetPress and hold BAKE pad for 5 seconds
  • Test Mode1
  • Verify fuel typePress and hold START/ENTER key for 5 seconds

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass