mypros+
Model reference

Amana RC-10SE/P76881-6M

Microwave

2 documents44 error codes17 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W11467195 - Rev B24 pg
    Covers this model

Installation Guide

  • Instrucciones de instalacion38 pg
    Covers this model
MyPros+ Max

Diagnose your Amana RC-10SE/P76881-6M.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (44)

CodeMeaning
AFRestricted/low air flow detected that may affect dryer performance.F0 E7Low Voltage ErrorF1 E1ACU (Appliance Control Unit) fault detected.F1 E4UIC (User Interface Control) fault detected.F1 E6Voltage input fault detected.F1 E7Voltage input fault detected.F1E1Indicates a CCU (Cycle Control Unit) problem.F2 E1Dryer keypad stuck errorF2 E2Upper Dryer Keypad Stuck ErrorF2E1Stuck button (depressed for over 20 seconds) or UI mismatch; only appears in…F2E2UI software error; UI cannot read EEPROM software.F3 E1Thermistor faultF3E1Exhaust thermistor is open; temperature drops below 18°F (>50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (<500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms)F3E4Inlet thermistor is shorted; temperature above 760°F (<20 ohms)F3E5Both inlet and exhaust thermistors are open; will occur if P14 connector is not…F3E6Moisture sensor strip is openF3E7Moisture sensor strip has shortedF4E1No voltage detected at the heater relayF4E3Restricted air flow detected that may affect dryer performance.F4E4Low L2 voltage (less than 30V) detected at the CCU.F5 E1Dryer door circuit error.F5 E6Upper Dryer Door Circuit ErrorF6 E1Communication failure between ACU and UICF6E1Communication error from UI to CCU; communication has not been detected.F6E2Communication error from CCU to UI; communication has not been detected.F7 E6Lower Dryer Motor Circuit ErrorF7 E7Upper Dryer Motor Circuit ErrorF7 E8Lower Dryer Motor Sense Error
View all 44 error codes
F7 E9Upper Dryer Motor Sense ErrorFC E1Model/Serial number not programmed.FC E2Model/Serial number not matching between ACU and UIC.FC E3Wi-Fi connection fault.FC E4USB stick failure (USB full, not detected, or not accessible).FC E5Software update failureFC E6Model setup export failureFC E7Model setup import failureFC E8Wi-Fi module not responding or not connected.FP E1Coin 1 circuit error.FP E2Coin 2 circuit error.FP E3Card reader communication error.L2Low L2 voltage (less than 30V) detected at the CCU.PFPower failure occurred while the dryer was running.

Service modes (17)

  • Component ActivationFrom Service Diagnostics Diagnostics Home screen, select 'Component Activation'
  • Diagnostic Mode["Enter Setup Mode first.","Press DELICATES keypad for one second while in any of the set-up codes…
  • Diagnostic Mode (Field Diagnostic Cycle)["Enter Setup Mode first.","Navigate to set-up code 6 or 7 (or while dAS displays if operating with…
  • diagnostic_modePress DELICATES keypad for one second while in any of the set-up codes 1 through 6 (or while dAS…
  • Help Mode["Enter Setup Mode first.","Navigate to set-up option 2.XX (or while dAS displays if operating with…
  • help_modePress HEAVY DUTY keypad while in special pricing option step 2.XX (or while dAS displays if…
  • model_serial_number_menuEnter Help Mode first
  • Model/Serial Number Menu["Enter Help Mode.","While on the S0 screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • Quick Diagnostic TestFrom Service Diagnostics, navigate to Error Diagnostic, then select 'Quick Diagnostic Test'
  • Service Diagnostics1. Ensure dryer is in standby mode (plugged in with all indicators off). 2. Select any three…
  • Setup Mode["COIN Models
  • Setup Mode (Control Set-Up)["PD Models
  • setup_modeCOIN Models
  • UI Component TestFrom Service Diagnostics, navigate to Component Activation, then select 'UI Component Test'
  • USB Menu["Enter Help Mode.","While on the USB screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • usb_menuEnter Help Mode first
  • wifi_menuWhile in setup mode on the F0 screen, press the HEAVY DUTY keypad to enter Wi-Fi mode.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass