mypros+
Model reference

Amana RO-700/P75992-1M

Microwave

6 documents56 error codes26 service modes

Available documentation

Tech Sheet

  • Tech Sheet2 pg
    Covers this model
  • TechSheet W10918575 RevB32 pg
    Covers this model
  • Tech Sheet - W103899578 pg
    Covers this model

Tech Tip

  • Instruction Sheet - 397875116 pg
    Covers this model
  • Instruction Sheet - 397972312 pg
    Covers this model
  • Instruction Sheet - 3978720 - Rev A12 pg
    Covers this model
MyPros+ Max

Diagnose your Amana RO-700/P75992-1M.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (56)

CodeMeaning
:Flashing colon indicates a power failure has occurred.AFLow inlet air flow detected at install.d13Coin 2 errord16Generation 2 debit card reader errord5Coin 1 errord9Low voltage detection errorF:01Primary control failure.F:02Stuck button or user interface mismatch (appears ONLY in Diagnostic Test Mode).F:20No voltage detected at the heater relay (appears ONLY in Diagnostic Test Mode).F:22Outlet thermistor is open.F:23Outlet thermistor has shorted.F:24Inlet thermistor is open (appears ONLY in Diagnostic Test Mode).F:25Inlet thermistor is shorted (appears ONLY in Diagnostic Test Mode).F:26Motor drive system failure.F:28Moisture sensor strip is open (appears ONLY in Diagnostic Test Mode).F:29Moisture sensor strip has shorted (appears ONLY in Diagnostic Test Mode).F:30Restricted air flow condition exists (appears ONLY in Diagnostic Test Mode).F:31Low voltage condition (less than 30 V) detected (appears ONLY in Diagnostic…F:50No voltage detected at the water valve relay (appears ONLY in Diagnostic Test…F:70No communication between the machine control and the console electronics.F:71No communication between the machine control and the console electronics.F:72Console electronics failure (F:72 through F:78).F:73Console electronics failure (F:72 through F:78).F:74Console electronics failure (F:72 through F:78).F:75Console electronics failure (F:72 through F:78).F:76Console electronics failure (F:72 through F:78).F:77Console electronics failure (F:72 through F:78).F:78Console electronics failure (F:72 through F:78).F01CCU errorF04Accelerometer failure
View all 56 error codes
F11Motor Control Unit (MCU) has a failure, possibly a repeating under or…F1E1Motor or heater failure.F1E4MW relay (Relay 4903) failureF2Touch panel failure.F20No water detected entering washerF21Long drainF22Door lock errorF24Temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionF28Communication failure between CCU and MCU.F29Door unlock errorF2E1Touch panel failure.F31Overheating of motorF33Pump disconnectedF34Load detected in washer during Washer Cleanout Cycle.F3E1Open or shorted exhaust thermistor.F3E2Open or shorted moisture sensor.F6MW relay failure (Relay 4903 on PCBA); relay contact may have welded closed.F6E1Communication error between HMI and ACU.F70Communication failure between CCU and UI (User Interface).F73UI failureF74UI failureL2Low line voltage (less than 30 V) detected at installation.PFPower failure occurred while the dryer was running.

Service modes (26)

  • Code Display Mode["This mode can be accessed only when the washer is in error state.","Open the service door.","The…
  • Code Display Sub-Mode["Open the service door when the washer is in an error state.","The current F code or d code will…
  • Customer-Focused Drying Mode Adjustment["In Standby mode (dryer plugged in but not powered up), press and hold the Dryness Level button…
  • Cycle Credit["Enter Flashing Mode (entire display flashing).","Press the HOT button (CC will display)."]
  • Error Code Display/Clear["From Service Diagnostic Mode, momentary press the 3rd button to display next error code.","Press…
  • Flashing Mode (Diagnostic Sub-Mode)["Open the service door.","Press and hold the COLD button until display segments are…
  • Help Mode["Enter set-up mode.","Press the WARM button until set-up code 2.XX is on display.","Press the HOT…
  • Help Mode (via dAS mode)["Enter set-up mode.","The message dAS will appear in the display.","Press the HOT button.","Press…
  • Help Mode (via Manual Communication)["Enter set-up mode.","Press the WARM button until the set-up code 2.XX is on display.","Press the…
  • Key Activation and Encoder Test["From Service Diagnostic Mode, momentary press the 1st button used in entry sequence."]
  • Manual Load Test["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…
  • Manual Overview Test["Enter Flashing Mode (entire display flashing).","Press the COTTON/WHITES button."]
  • Quick Overview Test["Enter Flashing Mode (entire display flashing).","Press the WARM button."]
  • Quick Spin Cycle["Enter Flashing Mode (entire display flashing).","Press the PERM PRESS button."]
  • Service Access Code (alternate setup entry without removing console)["If the washer is not in failure mode, open the door.","Press the upper left button.","Press the…
  • Service Access Code (No Console Removal)["Press the upper left button.","Press the lower right button.","Press the upper right…
  • Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Select any three (3)…
  • Service Diagnostic Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…
  • Service Test Mode["Enter Service Diagnostic Mode first.","Press and release the 2nd button used in the Service…
  • Setup Mode["Insert access door key, turn, and lift to remove access door.","Alternatively, if a debit card…
  • Software Version Display["From Service Diagnostic Mode, press and hold the 2nd button used in entry sequence for 5…
  • Touch Panel and ACU Test (Diagnostic/Test Mode)["Plug in microwave oven or reconnect power.","Press Cancel button to go to standby (colon ':'…
  • Touch Panel and PCBA Self-Diagnostic Test Mode["Press and hold the CANCEL/OFF button while opening the door.","While still holding the CANCEL/OFF…
  • Washer Cleanout Cycle["Enter Flashing Mode (entire display flashing).","Press the COLORS/DELICATES button."]
  • Washer Diagnostic Mode["First enter 'Start Operating Set-Up' (setup mode).","Press and hold the COLD button for 2 seconds…
  • Washer Diagnostic Mode (Flashing Mode)["Enter Setup Mode (open service access door or insert set-up card).","Press and hold the COLD…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass