mypros+
Model reference

Amana RR-7B

Microwave

6 documents46 error codes16 service modes

Available documentation

Tech Sheet

  • Tech Sheet12 pg
    Covers this model
  • Tech Sheet - 820601020 pg
    Covers this model
  • Tech Sheet - 82058778 pg
    Covers this model
  • Whirlpool Microwave MH1170XSB0 Tech Sheet12 pg
    Covers this model
  • Tech Sheet whirlpool dryer W10606148 Rev C60 pg
    Covers this model

Installation Guide

  • Installation Instructions16 pg
    Covers this model
MyPros+ Max

Diagnose your Amana RR-7B.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (46)

CodeMeaning
:Flashing colon indicates a power failure has occurred.F0 E7Control board recognized line voltage below 90 VAC.F1 E1ACU (Appliance Control Unit) fault.F1 E7ACU voltage input fault.F1E1Indicates a CCU (Cycle Control Unit) problem.F1E7PCB thermistor open or shorted.F2Membrane switch failure.F2 E1Lower dryer keypad is sensed pressed for 60 seconds (stuck key).F2 E2Upper dryer keypad is sensed pressed for 60 seconds (stuck key).F2E0Keypad disconnected.F2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; this…F2E2User Interface software errorF3E0Main oven sensor open or shorted.F3E1Exhaust thermistor is open; temperature drops below 18°F (>50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (<500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms).F3E4Inlet thermistor has shorted; temperature above 391°F (<328 ohms).F3E5Inlet and exhaust thermistors are both open; will occur if P14 connector is not…F3E6Moisture sensor strip is open; this fault code will only appear when in the…F3E7Moisture sensor strip has shorted; this fault code will ONLY appear when in the…F4E1No voltage detected at the heater relay; this fault code appears ONLY when in…F4E3Restricted/low air flow detected that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at the CCU.F5 E1Lower dryer door circuit error.F5 E6Upper dryer door circuit error.F5E0Door and switches do not agree (Clean modeF6Microwave relay failure.F6E1Communication error from UI to CCU; communication between the CCU and UI has…F6E2Communication error from CCU to UI; communication between the CCU and UI has…F6E3Over temperature (warming drawer).
View all 46 error codes
F7 E6Lower dryer motor circuit error.F7 E7Upper dryer motor circuit error.F7 E8Lower dryer motor sense errorF7 E9Upper dryer motor sense errorFC E1Model/Serial number not programmed into control.FC E4USB stick failure (USB full, not detected, or not accessible).FC E5Software uploaded from USB stick does not match the model number of the machine.FP E1Coin 1 circuit errorFP E2Coin 2 circuit errorFP E3Card reader communication error.L2Low L2 voltage (less than 50V) detected at the CCU.NTC OPENHood thermistor is open (displays 'NTC OPEN, CALL FOR SERVICE').NTC OPEN, CALL FOR SERVICEHood thermistor is open circuit.NTC SHORTHood thermistor is shorted (displays 'NTC SHORT, CALL FOR SERVICE').NTC SHORT, CALL FOR SERVICEHood thermistor is shorted.PFPower failure occurred while the dryer was running.

Service modes (16)

  • Customer-Focused Dryness Level Adjustment["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS LEVEL button…
  • Diagnostic Mode["Enter Setup Mode first.","While in any of the set-up codes 1 through 6 (or while dAS displays if…
  • Fault Code Display and Clear["Activate Service Diagnostic Mode first.","Press and release the 3rd button to display saved fault…
  • Help Mode["Enter Setup Mode first.","While in special pricing option step 2.XX (or while dAS displays if…
  • Install Diagnostics["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
  • Loads Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Within 5 seconds: Press…
  • Model/Serial Number Menu["Enter Help Mode.","While on the S0 screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • Self-diagnostic / Test Mode["Press and hold OFF/CANCEL while opening the door.","While still holding OFF/CANCEL, unplug the…
  • Self-Diagnostic Test Mode["Press and hold the OFF/CANCEL button while opening the door.","While still holding the OFF/CANCEL…
  • Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Select any three buttons…
  • Service Diagnostic Mode (Auto Test)1
  • Setup Mode["Stacked PD Models
  • Software Version Display["First activate Service Diagnostic Mode.","Press and hold the 2nd button used to activate Service…
  • USB Menu["Enter Help Mode.","While on the USB screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • User Interface Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
  • User Interface/Control System Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass