Model reference
Amana ASC-1B
Range
11 documents79 error codes15 service modes
Available documentation
Tech Sheet
- TECH SHEET - 9762977 - Rev A6 pg
- Fiche Technique6 pg
- Tech Sheet - W100464608 pg
- Tech Sheet - do not Discard6 pg
- TECH SHEET - 9762981 - Rev A6 pg
- Whirlpool Range GR563LXSS1 Tech Sheet6 pg
- FICHE TECHNIQUE - W10041710 - Rev A (FR)8 pg
- Tech Sheet - W100465908 pg
- Tech Sheet - W100467208 pg
Installation Guide
- Installation Instructions32 pg
Other
- R0233001_R0233001168 pg
MyPros+ Max
Diagnose your Amana ASC-1B.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (79)
CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board, or incompatible software…10-1Dispenser electrical problem10-3Drying fan error2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface cannot communicate with main control3-1Open connector or component in temperature sensing circuit (open or faulty…3-2Shorted connection or component in temperature sensing circuit, shorted or…3-3OWI calibration failure due to OWI sensor failure or drain hose check valve not…4-3Wash motor not running due to loose connection in motor circuit, faulty wash…5-1Door stuck open5-2Door stuck closed6-1Low or no water6-2Fill valve electrical problem6-3Suds or air in pump causing repeated wash periods.6-4Float switch open6-7Disconnected or damaged flowmeter.6-8Regen valve electrical problem7-1No heat7-2Heater stuck on8-2Drain motor electrical problem8-3Drain motor stuck on9-1Diverter can't find position9-2Diverter stuck on9-3Diverter disk in sump is missing.9-4Lower spray arm errorCLrNo error(s) found; no corrective action required.E0-F1EEPROM checksum error or EEPROM communication error.E0-F2Oven sensor circuit open.E1-F1UL A/D errors.View all 79 error codes
E1-F2Door latch does not function (mismatch between door and switches).E2-F1EEPROM communication error.E2-F2Latch error during self-clean operation.F0 E0No failure (default).F1Control failureF1 E0Internal error.F1 E1Internal error.F1 E2Internal error.F1 E3Internal error.F1 E4Internal error.F1 E5Internal error.F1 E6Internal error.F1 E7Internal error.F1 E8Internal error.F1 E9Internal error.F1-E0EEPROM communications failure, possibly caused by power line noise or lightning.F1-E1EEPROM checksum failure, possibly caused by power line noise or lightning.F2Shorted key detected on control panel.F2 E0Stuck key (shorted key).F2 E1Keypad disconnect or keypad disconnected.F2-E0Key contact closed for more than 60 seconds due to key held down too long…F2-E1No communication between keyboard and control due to keytail being loose…F3Oven sensor shortedF3 E0Main oven sensor open (top oven sensor opened).F3 E1Main oven sensor short (top oven sensor shorted).F3 E2Meat probe shorted.F3 E3CLEAN range over temperature.F3 E4Bottom oven sensor open.F3 E5Bottom oven sensor short (lower sensor short).F3 E6Warming drawer sensor open.F3 E7Warming drawer sensor shorted.F3-E0Break (open) in oven sensor circuit due to open sensor, loosened or…F3-E1Short in oven sensor circuit due to shorted sensor, sensor shorted to casing…F3-E2BAKE/BROIL temperature out of range (too high)F3-E3Clean temperature out of range (too high)F4 E2Over temperature during cook mode.F4 E3Over temperature during clean mode.F4 E7Over temperature cavity 2 (temperature runaway error).F5Door and switches do not agreeF5 E0Door latch mismatch (door and latch switches do not agree).F5 E1No operating latch (latch not operating).F5 E2Door switch fault.F5 E4Latch switch fault.F5 E7Unlock door error (cannot unlock door).F5-E0Door switch open during clean cycle due to switch failing open, open or loose…F5-E1Latch switch not operatingF6 E4Lost communication between display board and power board.F6 E5Cancel key error.GoodNo failure detected; displays only when user enters diagnostic mode and there…
Service modes (15)
- Diagnostic ModeWith oven not in bake, broil, or clean mode, press Cancel/OFF, Cancel/OFF, START in sequence…
- Diagnostic mode (error code recall)["Press the Cancel key to place the range in an idle state.","Press Cancel, Cancel, Start in that…
- Diagnostic mode (relay and switch testing)["Press the Cancel key to place the range in an idle state.","Press Cancel, Cancel, Start in that…
- Diagnostics ModeWith oven not in cooking, broiling, or cleaning mode, press Cancel/OFF, Cancel/OFF, START. The…
- Last fault code displayPress and hold CANCEL/OFF key for 5 seconds
- Last fault code retrievalPress and hold CANCEL/OFF key for 5 seconds to display the last error code.
- Manual Diagnostics Mode 1Enter within 120 seconds of power-up
- Manual Diagnostics Mode 2Enter after 120 seconds of power-up
- Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
- Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
- Temperature AdjustmentPress and hold BAKE for 5 seconds
- Temperature Adjustment (Calibration)Press and hold BAKE pad for 5 seconds
- Temperature Adjustment ModePress and hold BAKE key for 5 seconds
- Test modeWithin 60 seconds of power up, simultaneously hold down the BAKE and CLOCK keys for 5 seconds
- Test mode (diagnostic)Within 60 seconds of power up, simultaneously hold down the BAKE and CLOCK keys for 5 seconds
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana range models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass