Model reference
Amana CC-10/P72771-10S
Range
48 error codes18 service modes
MyPros+ Max
Diagnose your Amana CC-10/P72771-10S.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (48)
CodeMeaning
d13Coin 2 sensor is detected as blocked; coin vault may be full or sensor may be…d16Gen. 2 debit card reader errord5Coin 1 sensor is detected as blocked; coin vault may be full or sensor may be…d9Low voltageF01Indicates a main control fault.F03Main control detects an out of range pressure signal from the pressure…F07Main control cannot determine position of shifter (shifter system failure).F0E4Off balance load detected during cycle operation.F11Motor control faultF1E1A fault has occurred in the main control.F1E7Control board recognized line voltage below 90 V AC.F20Long fillF21Long drainF22Lid lock faultF24Inlet water temperature faultF25Basket speed sensor faultF26Lid switch faultF27Overflow conditionF29Lid unlock faultF2E1Washer keypad is sensed pressed for continued duration.F32No fillF3E1Main control detects an out of range pressure signal.F3E2Inlet thermistor is detected to be open or shorted.F5E1Lid is in locked state but lid switch is open; main control cannot detect the…F5E3Lid lock has not moved into locked position or motor cannot be powered; lid not…F5E4Lid lock has not moved into unlocked position or motor cannot be powered.F70Communication failure between CCU and UIF71Communication failure between CCU and UIF73The User Interface identification does not match the expected value in the Main…F74The User Interface identification does not match the expected value in the Main…View all 48 error codes
F77Off balance load detected.F7E1Main control cannot determine speed of basket, or speed changes too quickly…F7E5Main control cannot determine position of shifter.F7EDFault of the motor control section of the main control.F8E1No fillF8E3Overflow conditionF9E1Long drainFCE1No model/serial number information is saved on the machine's controls.FCE2Model/serial number information saved on the machine's controls is not the same…FCE3Wi-Fi connection fault.FCE4USB stick failure (USB full, not detected, or not accessible).FCE5Software uploaded from USB stick does not match the model number of machine.FCE6Download of machine setup from machine to USB stick failed.FCE7Upload of machine setup from USB stick to machine failed; machine number from…FCE8Wi-Fi module not responding or not connected.FPE1Coin 1 circuit error.FPE2Coin 2 circuit error.FPE3Card reader communication error.
Service modes (18)
- Calibration Cycle (P-05)["Enter Service Diagnostic Test Modes.","Press MIXED keypad until 'P-05' is displayed.","Press…
- Help Mode["Enter Service Mode.","Use MIXED keypad to advance to program location 2.xx (Special Pricing…
- Manual Overview Test (P-04)["Enter Service Diagnostic Test Modes.","Press MIXED keypad until 'P-04' is displayed.","Press…
- P-01 Clear Errors["Access Service Diagnostic Test Modes.","Display shows 'P-01'.","Press START to clear an active…
- P-02 Cycle Credit["Access Service Diagnostic Test Modes.","Press NORMAL to step to 'P-02'.","Press START to provide…
- P-03 Service Diagnostic["Access Service Diagnostic Test Modes.","Press NORMAL to step to 'P-03'.","Press START to initiate…
- P-04 Manual Diagnostic["Access Service Diagnostic Test Modes.","Press NORMAL to step to 'P-04'.","Press START to initiate…
- P-05 Calibration Cycle["Access Service Diagnostic Test Modes.","Press NORMAL to step to 'P-05'.","Press START to initiate…
- P-07 UI Diagnostics["Access Service Diagnostic Test Modes.","Press NORMAL to step to 'P-07'.","Press START to start UI…
- P-09 Tachometer Verification["Access Service Diagnostic Test Modes.","Press NORMAL to step to 'P-09'.","Press START to start…
- P-12 Clean Washer Cycle["Access Service Diagnostic Test Modes.","Press NORMAL to step to 'P-12'.","Press START to start…
- Quick Overview Test (P-03)["Enter Service Diagnostic Test Modes.","Press MIXED keypad until 'P-03' is displayed.","Press…
- Service Diagnostic Test Modes["For coin models
- Service Diagnostic Test Modes (entry)["For coin (PD) models
- Set-Up Mode (Control Programming)["Coin Models
- Tachometer Verification (P-09)["Enter Service Diagnostic Test Modes.","Press MIXED keypad until 'P-09' is displayed.","Press…
- Technician Service Access Code (Non-Coin Free Vend models only)["Press the HEAVY DUTY, EXTRA RINSE, TEMPERATURE, and DELICATES keypads within 10 seconds."]
- UI Diagnostics (P-07)["Enter Service Diagnostic Test Modes.","Press MIXED keypad until 'P-07' is displayed.","Press…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana range models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass