mypros+
Model reference

Amana RCC-1010/P85729-1S

Range

8 documents50 error codes14 service modes

Available documentation

Service Manual

  • jobaid 4317323 kac 2860 pg
    Covers this model
  • Technical Education Job Aid 4317323 KAC-28 Electric Built-in Single Oven60 pg
    Covers this model
  • Service Manual - 432168957 pg
    Covers this model
  • Whirlpool & KitchenAid Built-In Electric Cooktops42 pg
    Covers this model

Installation Guide

  • Installation Instructions4 pg
    Covers this model
  • Installation Instructions4 pg
    Covers this model
  • Installation Instructions4 pg
    Covers this model
  • Installation Instructions20 pg
    Covers this model
MyPros+ Max

Diagnose your Amana RCC-1010/P85729-1S.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (50)

CodeMeaning
d13Coin 2 errord16Generation 2 debit card reader errord5Coin 1 errord9Low voltage detection errorF0Default F codeF01CCU errorF1Electronic control malfunction (all E codes).F1-E0Key held down too long, or key is shorted.F1-E1Keypad keytail not connected.F1-E5Cancel key drive line open.F11MCU errorF2Electronic control malfunction.F2 E0Key held down too long, or key is shorted.F2 E1Keypad keytail not connected.F2 E5Cancel key drive line open.F20No water detected entering washerF21Long drainF22Door lock errorF24Temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionsF28Communication failure between CCU and MCU.F29Door unlock errorF3 E0Temperature sensor opened.F3 E1Temperature sensor shorted.F3 E2Oven temperature too high (over 301°C / 575°F in Cook mode).F3 E3Oven temperature too high (over 510°C / 950°F in Clean mode).F3-E0Temperature sensor opened.F3-E1Temperature sensor shorted.
View all 50 error codes
F3-E2Oven temp too high (over 301°C [575°F] in Cook mode).F3-E3Oven temp too high (over 510°C [950°F] in Clean mode).F31Overheating of motorF33Pump disconnectedF34Load detected in washer during Washer Cleanout Cycle.F4 E1Meat probe malfunctionF4-E1Meat probe malfunctionF5 E0Door is open but latch is locked (door switch closed indicating open door, and…F5 E1Self-clean latch will not lock.F5 E5Self-clean temperature (288°C / 550°F) not reached within 45 minutes.F5 E7Self-clean latch will not unlock.F5-E0Door is open, but latch is locked (door switch closed indicating open door, and…F5-E1Self clean latch will not lock.F5-E5Self clean temperature (288°C [550°F]) not reached within 45 minutes.F5-E7Self clean latch will not unlock.F6 E0Return line not connected; electronic control will display F6 within 60 seconds…F6-E0Return line not connected.F70Communication failure between CCU and UI (User Interface).F73UI failureF74UI failure

Service modes (14)

  • Cycle Credit (Free Cycle)["Enter diagnostic mode (entire display flashing).","Press the HOT button (CC will display)."]
  • Fahrenheit to Celsius conversionPress the BROIL pad for 5 seconds
  • Fault code history recallPress and hold the '0' touchpad for 5 seconds to access the previous fault codes
  • Help Mode (DA Communication Established)["Open the service door.","The message dAS will appear in the display.","Press the HOT button to…
  • Help Mode (Manual Communication)["Open the service door.","Press the WARM button until the set-up code 2.XX is displayed.","Press…
  • Manual Overview Test["Enter diagnostic mode (entire display flashing).","Press the COTTON/WHITES button."]
  • Programming Cavity SizeWithin 60 seconds of power up, press
  • Programming the cavity sizeWithin 60 seconds of power up, press the following touchpads in order
  • Quick Overview Test["Enter diagnostic mode (entire display flashing).","Press the WARM button."]
  • Quick Spin Cycle["Enter diagnostic mode (entire display flashing).","Press the PERM PRESS button."]
  • Sabbath Mode exitIf 'SAB' appears in the display, press and hold the '6' touchpad for 5 seconds to end Sabbath Mode.
  • Washer Cleanout Cycle["Enter diagnostic mode (entire display flashing).","Press the COLORS/DELICATES button."]
  • Washer Diagnostic Mode (via Key Dance - 9060 non-coin models with $0 vend price)["Key dance must be performed within 60 seconds.","Press Cottons/Whites button.","Press Cold…
  • Washer Diagnostic Mode (via Service Access Door)["Open the service access door on top of the metercase (9050 models

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass