Model reference
Caloric DCR-211-1N-OK
Dishwasher
3 documents65 error codes21 service modes
Available documentation
Tech Sheet
- Tech Sheet - W10195615 - Rev B2 pg
- Kitchnaid Dishwasher KUDC10FXSS0 KUDC10FXSS1 KUDC10FXSS2 KUDC10FXSS3 Tech Sheet2 pg
- Kitchenaid Dishwasher KUDS30IXWH4 Tech Sheet2 pg
MyPros+ Max
Diagnose your Caloric DCR-211-1N-OK.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (65)
CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Control software issue10-1Dispenser electrical problem10-2Vent wax motor electrical problem10-3Drying fan error2-1Stuck key or short circuit(s) in keypad or in control's input lines that read…2-2Model has an LCD display and the control has been exchanged for one that is not…3-1Open or faulty temperature sensor, or faulty temperature sensor input on…3-2Shorted connection or component in Temperature Sensing Circuit, shorted or…3-3OWI (Optical Water Indicator) soil sensor failure.4-3Wash motor not running5-1Door stuck open5-2Door stuck closed6-1Low/no water (mechanical problem)6-2Fill valve electrical problem6-3Suds/air in pump6-4Float switch open6-6Cool water6-7Flow meter problem6-8Water softener regeneration valve electrical problem (water softener models…7-1No heat7-2Heater stuck on8-1Slow drain8-2Drain motor electrical problem8-3Drain stuck on9-1Dispenser electrical problemCLrNo error(s) foundE-08Control board failure requiring replacement.E-09Control board failure requiring replacement.E-10Shorted or open keypad.View all 65 error codes
F0Default F codeF01Oven temperature sensor circuit is open.F02Welded element relays detected.F05Door or latch problems.F06Electronic control malfunction.F1Electronic control malfunction.F1-E0Key held down too long, or key is shorted.F1-E1Keypad keytail not connected.F1-E5CANCEL key drive line open.F1E1Indicates a CCU (Cycle Control Unit) problem.F2Shorted key detected on the control panel.F2-E0Temperature sensor opened (R=2875 ohm by spec).F2-E1Temperature sensor shorted (R=825 ohm by spec).F2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; only…F3Oven temperature sensor opened or shorted.F3-E2Oven temp too highF3-E3Oven temp too highF3E1Exhaust thermistor is open; temperature drops below 18°F (>50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (<500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms).F3E4Inlet thermistor has shorted; temperature above 391°F (<328 ohms).F3E5Inlet and exhaust thermistors are both open; will occur if P14 connector is not…F3E6Moisture sensor strip is open; only appears in service diagnostic mode.F3E7Moisture sensor strip has shorted; only appears in service diagnostic mode.F4-E1Meat probe malfunctionF4E1No voltage detected at the heater relay; only appears in diagnostic test mode.F4E3Low air flow detected that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at the CCU.F5Door and door switches do not agree (mismatch between door position and switch…F5-E0Door is open but latch is locked (door switch open indicating open door, latch…F5-E1Self-clean latch will not lock/unlock.F6E1Communication between CCU and UI has not been detected (UI to CCU communication…F6E2Communication between CCU and UI has not been detected (CCU to UI communication…L2Low L2 voltage (less than 50V) detected at the CCU.PFPower failure occurred while the dryer was running.
Service modes (21)
- Bake Temperature Offset Adjustment1
- Cavity Size ProgrammingWithin 60 seconds of power up, press the following touchpads in order
- Clear Customer Error HistoryDuring Service Diagnostics Cycle interval 20, press Hi Temp key
- Customer-Focused Dryness Level Adjustment["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS LEVEL button…
- diagnostic_test["Door must be open","Set Temperature switch to Air Fluff","Set End of Cycle Signal switch to…
- Diagnostics ModeWith the oven not in cooking or broiling mode, press Cancel/OFF > Cancel/OFF > START. The display…
- Fahrenheit to Celsius ConversionPress the BROIL pad for 5 seconds
- Fault Code History RecallPress and hold the '0' key to access previous fault codes
- Install Diagnostics["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
- less_dry_test["Begin with a fully assembled, empty dryer with clean lint screen","Dryer must be connected to a…
- Loads Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Within 5 seconds: Press…
- Rapid Advance Mode (Cycle Operation)After starting a cycle (door open or closed), press Hi Temp
- Rapid Advance Mode (during customer cycle)Press HI TEMP
- Sales Demo Mode ExitRun Service Diagnostics Cycle to clear Demo mode.
- Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Select any three buttons…
- Service Diagnostics CycleWith dishwasher in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1…
- Service Test Mode (Electronic Control Panel)["Open oven door.","Press and hold Pad 3 for 5 seconds to enter service test mode."]
- Service Test Mode (Electronic Dial Control Panel)["Open oven door.","Press and hold Hidden Pad 2 for 5 seconds to enter service test mode."]
- Software Version Display["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…
- Temperature Adjustment ModePress and hold BAKE key for 5 seconds
- User Interface Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Caloric dishwasher models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax