mypros+
Model reference

Caloric DCR-211-1W-OM

Dishwasher

2 documents52 error codes14 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10505257 - Rev A16 pg
    Covers this model
  • Tech Sheet12 pg
    Covers this model
MyPros+ Max

Diagnose your Caloric DCR-211-1W-OM.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (52)

CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board, or incompatible software…10-1Dispenser electrical problem10-2Vent wax motor electrical problem10-3Drying fan error12-1No communication between ECM and control12-2No link between ECM and wireless router12-3No link between ECM and Internet12-4Antenna A problem12-5Antenna B problem12-6Current Transformer problem12-7Provisioning problem2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface problem (capacitive touch keypad adhesive, moisture, or debris…3-1Open connector or component in Temperature Sensing circuit; open or faulty…3-2Incoming water temperature above 167°F (75°C), or shorted connection/component…3-3OWI calibration failure4-3Wash motor not running due to loose connection in Motor circuit and/or faulty…5-1Door stuck open5-2Door stuck closed6-1Low/no water6-2Fill valve electrical problem6-3Suds or air in pump6-4Float switch open6-6Incoming water under 84°F (29°C)6-7Disconnected or damaged flowmeter.6-8Regen valve electrical problem7-1No heat7-2Heater stuck on8-1Slow drain
View all 52 error codes
8-2Drain motor electrical problem8-3Drain stuck on9-1Diverter can't find position9-2Diverter stuck on9-3Diverter disk missingF1E1Indicates a CCU (Cycle Control Unit) problem.F2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; this…F2E2UI cannot read EEPROM software from the User Interface.F3E1Exhaust thermistor is open; temperature drops below 18°F (> 50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (< 500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (> 245k ohms).F3E4Inlet thermistor is shorted; temperature above 391°F (< 328 ohms).F3E5Inlet and exhaust thermistors are both open; will occur if the P14 connector is…F3E6Moisture sensor strip is open; this fault code will only appear when in the…F3E7Moisture sensor strip has shorted; this fault code will ONLY appear when in the…F4E1No voltage detected at the heater relay; appears ONLY when in the Diagnostic…F4E3Restricted air flow that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at the CCU.F6E1Communication between the CCU and UI has not been detected (UI to CCU…F6E2Communication between the CCU and UI has not been detected (CCU to UI…L2Low L2 voltage (less than 50V) detected at the CCU.PFPower failure occurred while the dryer was running.

Service modes (14)

  • Customer-Focused Dryness Level Adjustment["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS LEVEL button…
  • diagnostic1
  • Error Code History DisplayEnter Service Diagnostics Cycle (1-2-3-1-2-3-1-2-3)
  • holiday_modePress the Holiday Mode key
  • Install Diagnostics["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
  • Loads Test Mode["Ensure the dryer is in standby mode (plugged in with all indicators off).","Within 5 seconds…
  • Rapid Advance (Customer Cycles)["Start a customer cycle.","Press HIGH TEMP
  • Rapid Advance ModePress HI TEMP
  • sales_demonstrationPress and hold the Max Cool and Power On/Off keys for 2 seconds.
  • Service Diagnostic Mode["Ensure the dryer is in standby mode (plugged in with all indicators off).","Select any three (3)…
  • Service Diagnostics Cycle["Press Start key to wake up the control panel.","Press any 3 keys in the sequence…
  • Software Version Display["First activate Service Diagnostic Mode.","Press and hold the 2nd button used to activate Service…
  • User Interface Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
  • User Interface/Control System Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Caloric dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax