mypros+
Model reference

Caloric DCR-225-1F-OK

Dishwasher

4 documents103 error codes32 service modes

Available documentation

Tech Sheet

  • Basic Operation of Commercial Stacked Washer/dryer20 pg
    Covers this model
  • Tech Sheet - W103503332 pg
    Covers this model
  • Whirlpool Dishwasher WDF530PLYW0 Tech Sheet2 pg
    Covers this model

Service Manual

  • Instruction Sheet - 854371916 pg
    Covers this model
MyPros+ Max

Diagnose your Caloric DCR-225-1F-OK.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (103)

CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board or incompatible software…1-3Control detected stuck key(s) in keypad or keypad connection.10-1Dispenser electrical problem10-2Vent wax motor electrical problem.10-3Drying fan error2-1User interface stuck key or short circuit(s) in keypad or in control's input…2-2Software or hardware incompatibility problem with control.3-1Open temperature sensing circuit3-2Shorted temperature sensing circuit3-3OWI/thermistor sensor failed calibration.4-3Wash motor not running5-1Door stuck open5-2Door stuck closed6-1Inlet water6-2Inlet water6-3Inlet water6-4Inlet water6-6Inlet water6-7Disconnected or damaged flowmeter.6-8Inlet water7-1Heating7-2Heating8-1Draining8-2Draining8-3Draining9-1Diverter9-2Diverter stuck on9-3Diverter disk missing from sump.C1Blocked coin 1 or coin drop control circuit failure (coin recognition and price…
View all 103 error codes
C2Blocked coin 2 or coin drop control circuit failure (coin recognition and price…CAAverage current limit trip; a 2-second average current draw greater than 5.55…CECommunications error; breakdown in communication between the machine controller…CIInstantaneous current limit trip; a spike of 26 Amps was detected instantly at…d 13Coin 2 errord 16Generation 2 debit card reader errord13Washer Coin 2 errord16Generation 2 debit card reader errord5Washer Coin 1 errord9Washer low voltage detection errorEdNot receiving communications from installed debit card reader in Enhanced…ErProcessor reset error; the control failed to save cycle information during a…error1Shorted sensor circuit.error2Open sensor circuit.error3On the cooling mode, sensor's Vout was not less than 4.7V within 3 minutes.error4On the way to sensing, the door was opened.F 01Dryer motor control circuit errorF 04Accelerometer failureF 11MCU errorF 20No water detected entering washerF 21Long drainF 22Door lock errorF 23Dryer exhaust thermistor shorted errorF 24Temperature sensor errorF 25Tachometer errorF 26Door switch errorF 27Overflow conditionsF 28Communication failure between CCU and MCU.F 29Door unlock errorF 31Overheating of motorF 33Pump disconnectedF 34Load detected in washer during Washer Cleanout Cycle.F 70Communication failure between CCU and UIC.F 71Dryer communication failure from UIC to dryer CCUF 73UIC failure (washer) / UIC Microprocessor error (dryer)F 74UIC EEPROM errorF01Washer CCU errorF04Washer accelerometer failureF11Washer MCU errorF1E1Primary control failure in the machine control electronics.F20Washer no water detected entering washerF21Washer long drainF22Washer door lock errorF23Dryer exhaust thermistor shorted errorF24Washer temperature sensor errorF25Washer tachometer errorF26Washer door switch errorF27Washer overflow conditionF28Washer communication failure between CCU and MCU.F29Washer door unlock errorF2E1Stuck button or user interface mismatch; only appears in service diagnostic…F31Washer motor overheatingF33Washer pump disconnectedF34Washer load detected during Washer Cleanout Cycle.F3E1Exhaust thermistor circuit is open.F3E2Exhaust thermistor has shorted.F3E6Moisture sensor strip is open; only appears in service diagnostic mode.F3E7Moisture sensor strip has shorted; only appears in service diagnostic mode.F70Washer communication failure between CCU and UIC.F71Dryer communication failure from UIC to dryer CCUF73Dryer UIC microprocessor errorF74Washer UIC EEPROM error.LdLong drain; it takes longer than 5 minutes to pump out water to the point where…LFLong fill; the water fill time exceeded 10 minutes, causing the water valves to…LSLid switch error; the control cannot detect lid switch opening/closing…LVVoltage detected below 90 VAC for 8 seconds.obOff balance; the motor controller detected an unrecoverable off-balance…PFPower failure detected during a running cycle; the washer lost power mid-cycle.SdLast drain occurring during final spin was slow.SFLast fill was slow.SLSuds lock; excessive suds detected and the unit was unable to clean out suds…SrStuck relay; the relay has failed in the closed position so the machine…tFWater temperature sense error when equipped with temperature sensing water…

Service modes (32)

  • Automatic Service DiagnosticsControl must be in Off state. Perform Key Dance within 5 seconds
  • Console Keypad and LED TestControl must be in Off state. Perform Key Dance within 5 seconds
  • Customer-Focused Drying Mode Adjustment1. Ensure dryer is in standby mode (plugged in with all indicators off, or only DONE indicator on)…
  • diagnostic mode["Enter set-up mode first.","While in any of the set-up codes 1 through 6, anytime a diagnostic…
  • Dryer Field Diagnostic Cycle["Enter Diagnostic Mode (entire display flashing).","Press the upper middle (PERM PRESS)…
  • Dryer Field Diagnostic Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the upper middle (PERM PRESS) button."]
  • Error History ReadingEnter Service Diagnostics Cycle. Error codes are displayed in intervals 24 (Error 1
  • field diagnostic cycle["Enter diagnostic mode (entire display flashing).","Press the LOWER MIDDLE key pad to start the…
  • help mode["Enter set-up mode first.","Navigate to special pricing option mode (code 2.XX).","Press the LOWER…
  • Manual DiagnosticsControl must be in Off state. Perform Key Dance within 5 seconds
  • Nutate and Recirculate TestControl must be in Off state. Perform Key Dance within 5 seconds
  • Rapid Advance Mode (Cycle Operation)After starting a cycle, press HI TEMP
  • Rapid Advance Mode (during active cycle)Press HI TEMP
  • Rapid Advance Mode (in-cycle)After starting a cycle, press HI TEMP
  • Service Diagnostic Mode1
  • Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
  • Service Diagnostics Error History ReadoutAfter entering Service Diagnostics Cycle, errors are displayed in intervals 24 (Error 1
  • set-up mode["PD Models
  • Set-Up Mode (Coin Payment)["Insert service switch key and turn counter-clockwise."]
  • Spin and Drain TestControl must be in Off state. Water should be present in the unit. Perform Key Dance within 5…
  • User Interface/Control System Test1
  • Washer Cleanout Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center right (COLORS/DELICATES)…
  • Washer Cleanout Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center right (COLORS/DELICATES)…
  • Washer Cycle Credit["Enter Diagnostic Mode (entire display flashing).","Press the lower left (HOT) button (CC will…
  • Washer Cycle Credit (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower left (HOT) button (CC will…
  • Washer Manual Overview Test Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center left (COTTON/WHITES) button."]
  • Washer Manual Overview Test Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center left (COTTON/WHITES) button."]
  • Washer Quick Overview Test Cycle["Enter Diagnostic Mode (entire display flashing).","Press the lower middle (WARM) button."]
  • Washer Quick Overview Test Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower middle (WARM) button."]
  • Washer Quick Spin Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center middle (PERM PRESS) button."]
  • Washer Quick Spin Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center middle (PERM PRESS) button."]
  • Water Inlet and Dispenser Valve Operating PS TestControl must be in Off state. Perform Key Dance within 5 seconds

Full entry steps, exit procedures, and test sequences are available in Max.

Related Caloric dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax