Model reference
KitchenAid KERS507XSS02
Range
4 documents30 error codes11 service modes
Available documentation
Tech Sheet
- Tech Sheet - W1034058516 pg
Service Manual
- Troubleshooting Gas and Electric Freestanding Range Electronic Controls70 pg
Installation Guide
- Installation Instructions20 pg
- Instruction Sheet1 pg
MyPros+ Max
Diagnose your KitchenAid KERS507XSS02.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (30)
CodeMeaning
F1Control failure or UL A/D error(s) detected in the control board.F1 E*Control board failure (all F1 sub-codes indicate control fault).F1-E0EEPROM communication error (oven control).F1-E1Upper RTD uncalibrated (oven control).F1-E2Lower RTD uncalibrated (oven control).F1-E5Sensor usage out of range (oven control).F1-E7PCB Thermistor/Sensor open or shorted (oven control).F1-E9WIDE Queue full (oven control).F2Shorted/stuck key detected on the control keypad.F2-E0Keypad disconnected (oven control).F2-E1Stuck key (cooktop control).F2-E2Stuck key (oven control).F3Oven sensor opened or oven sensor shorted.F3 E0Oven temperature sensor fault (open or shorted)F3 E1Lower oven temperature sensor fault (MRC II double oven models).F3 E2Warming drawer temperature sensor fault.F3-E0Main oven temperature sensor open or shorted (upper oven).F3-E1Main oven temperature sensor open or shorted (lower oven).F5 E0Door position switch faultF5 E1Door latch switch/system faultF5 E2Door switch fault.F5-E0Door and latch switches do not agree during Clean mode.F5-E1Door latch not operating during Clean mode.F6 E*Control communication failure.F6-E0Lost communications between control boards.F6-E1Over temperature during cook mode (runaway temp).F6-E2Over temperature during clean mode (runaway temp).F6-E3Over temperature in warming drawer (runaway temp).F9House miswiredF9-E0Product is mis-wired.Service modes (11)
- Cooktop Controls Diagnostic Mode["Press any 3 different keys in sequence.","Repeat this same 3-key sequence 2 more times within 13…
- LCC Diagnostic Mode (LCC90/LCC95/LCC180)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
- LCC190 Diagnostic Mode (Self Clean, Convection models)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME or TEMP/HOUR '+' key to cycle through…
- MRC Diagnostic Mode["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
- MRC Diagnostic Mode (Fan/True Convection Electric - Oven Light entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
- MRC II Diagnostic Mode (Number 3 key entry - KitchenAid models)["Press OFF/OFF/START or CANCEL/CANCEL/START in sequence.","Press the number '3' key to cycle…
- MRC II Diagnostic Mode (TEMP/TIME entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' keypad to cycle through diagnostic…
- Oven Diagnostics Mode["Press OFF, then OFF, then START within 5 seconds."]
- Semi Automatic Test Mode (Oven)["Enter Oven Diagnostics Mode (OFF > OFF > START within 5 seconds).","Press TEMP/TIME +/- or Number…
- Temperature Calibration Mode["Press SETTINGS/OPTIONS until 'Temp Calib' is highlighted.","Follow instructions to see the…
- Test Mode (Oven - Manual Relay Activation)["Enter Oven Diagnostics Mode (OFF > OFF > START within 5 seconds).","Press TEMP/TIME +/- or Number…
Full entry steps, exit procedures, and test sequences are available in Max.
Related KitchenAid range models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass