Model reference
KitchenAid KESH307HWH0
Range
6 documents33 error codes18 service modes
Available documentation
Tech Sheet
- TECH SHEET - KitchenAid Range KESH307HBS68 pg
Service Manual
- KitchenAid Electronic Range Controls "B" & "D" Line Wall Ovens Job Aid93 pg
Wiring Diagram
- KitchenAid Range KESC307HWH5 Wiring Sheet1 pg
Other
- Wiring Sheet 9753028 KA Range KESC307HBT42 pg
- 431716993 pg
Installation Guide
- Installation Instructions5 pg
MyPros+ Max
Diagnose your KitchenAid KESH307HWH0.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (33)
CodeMeaning
F0 E0No fault found.F1 E0EEPROM read fault (silent fault, not displayed).F1 E1EEPROM checksum does not match at start key (silent fault, not displayed).F1 E2Lost communication with power board.F1 E3Configuration jumper changeF1 E4Q8 shorted.F1 E5Meat probe not calibrated.F1 E6Display board EPROM access failure.F1 E7Power board EPROM access failure.F1 E8Improper keypad feedback from power board supply lift.F1 E9Stack overflow, highest priority fault.F1 EAExceeded stack warning level.F2 E0Cancel key level too low (open).F2 E1Cancel key invalid.F2 E2Cancel key loop test failed.F2 E3Key held down too long or keyboard short.F2 E4Keys unsettled, probably due to noise.F3 E0Oven temperature sensor (PLAT sensor) open.F3 E1Oven temperature sensor (PLAT sensor) shorted.F3 E2Oven temperature too high (runaway).F3 E3Shorted oven sensor.F3 E4Oven temperature too high (runaway condition).F4 E0Meat probe shorted (less than 1500 ohms).F4 E1Meat probe shorted (less than 1500 ohms).F5 E1Self-clean latch will not make after 30 seconds.F5 E3Loss of 120 VAC across L1 to ground, or Q19 circuit error.F5 E5Self-clean temperature not satisfied after 30 minutes.F5 E6Door locked with door open.F5 E7Door unlocked and will not unlatch.F6 E0Ambient sensor opened (too hot).Service modes (18)
- Convection Freestanding/Slide-In Control ProgrammingAfter unit is powered up, press the following keypad sequence
- End of Service Test Sequence (Convection Units)["Connect unit to power, set power ON and wait until CONTROL LOCK clears and display shows PF…
- End of Service Test Sequence (Non-Convection Units)["Connect unit to power, set power ON and wait until CONTROL LOCK clears and display shows PF…
- Hidden Functions - Bake Temperature CalibrationTouch and hold the Bake keypad for 5 seconds.
- Hidden Functions - Clock Display OffTouch and hold the Clock keypad for 5 seconds.
- Hidden Functions - DehydrateTouch and hold the Conv
- Hidden Functions - End-of-Cycle Tones OffTouch and hold the Cook Time keypad for 5 seconds.
- Hidden Functions - Fahrenheit/Celsius ToggleTouch and hold the Broil keypad for 5 seconds.
- Hidden Functions - Keypad Entry Tones OffTouch and hold the Stop Time keypad for 5 seconds.
- Hidden Functions - Keypad LockoutTouch and hold the #3 keypad for 5 seconds.
- Hidden Functions - Last F/E Code and ROM RevisionTouch and hold the #0 keypad for 5 seconds.
- Hidden Functions - Raising Bread DoughTouch and hold the Baked Goods keypad for 5 seconds.
- Hidden Functions - Range Configuration DisplayTouch and hold the #1 keypad for 5 seconds.
- Hidden Functions - Sell ModeTouch and hold the Timer Cancel keypad for 5 seconds.
- Hidden Functions - Timer Operating Tones OffTouch and hold the Timer Start keypad for 5 seconds.
- Hidden Functions - Tone Frequency ChangeTouch and hold the #7 keypad for 5 seconds.
- Non-Convection Freestanding/Slide-In Control ProgrammingAfter unit is powered up, press the following keypad sequence
- Sabbath Mode1
Full entry steps, exit procedures, and test sequences are available in Max.
Related KitchenAid range models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass