mypros+
Error code reference

KitchenAid Range Error Code F4 E0

Meat probe shorted (less than 1500 ohms).

KitchenAid codesKitchenAid range codes

Meat probe shorted (less than 1500 ohms).

First step from the service manual

Replace meat probe.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F4 E0.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F4 E0 means on a KitchenAid range

F4 E0 indicates the control board has detected a short circuit in the meat probe circuit, with resistance measuring below 1500 ohms. This threshold exists because a properly functioning probe reads resistance values in a specific range that corresponds to temperature; when resistance drops this low, the board interprets the probe as shorted and throws the fault. The code points directly at the meat probe itself or the probe socket on the range.

For homeowners, the meat probe is the temperature sensor you plug into the side of the oven cavity to monitor the internal temperature of roasts or other large cuts of meat. When the control board sees a resistance reading that is too low, it means the probe is sending a bad signal, usually because the probe has failed internally, the probe jack has been damaged, or moisture or grease has gotten into the connection. The range triggers this code to prevent inaccurate temperature readings that could result in undercooked food.

In most cases, the probe itself is the failed component. Meat probes are exposed to high heat, grease, and physical handling over time, all of which degrade the internal thermistor. Replacing the probe is the first and most likely fix. If a new probe does not clear the code, the probe socket or wiring harness between the socket and control board should be inspected next.

Source: manufacturer service documentation.

Common causes of F4 E0

  1. 01

    Failed meat probe (internal short)

    Part replacement

    The thermistor inside the meat probe has shorted, dropping resistance below 1500 ohms. This is the most common cause and is typically the result of heat exposure, physical damage, or normal wear over time.

  2. 02

    Grease or moisture in the probe socket

    Wiring / connection

    Contamination inside the probe jack on the oven wall can create a low-resistance path that mimics a shorted probe. Cleaning the socket thoroughly may resolve the fault if the probe itself tests within normal resistance range.

  3. 03

    Damaged probe socket or jack

    Part replacement

    The socket built into the oven cavity can sustain physical damage or corrosion that causes a short in the circuit independent of the probe. If a known-good probe still triggers F4 E0, the socket likely needs replacement.

  4. 04

    Wiring harness short between probe socket and control board

    Part replacement

    A pinched, burned, or chafed wire in the harness connecting the probe jack to the control board can create a short that reads as a probe fault. This is less common but should be inspected if replacing the probe and socket do not resolve the code.

See the test procedure for each cause

Frequently asked questions about F4 E0

What does F4 E0 mean on a KitchenAid range?
F4 E0 means the control board detected a short in the meat probe circuit, with resistance measuring below 1500 ohms. The meat probe is the temperature sensor you plug into the oven wall to monitor food temperature. This code tells you the probe is sending an invalid signal, most often because the probe itself has failed internally.
How do I fix F4 E0 on a KitchenAid range?
Start by unplugging the meat probe if it is currently connected and see if the error clears. If the code appeared with a probe plugged in, replace the probe with a compatible KitchenAid meat probe. If you do not use a meat probe and the code still appears, inspect the probe socket on the oven wall for visible damage or contamination. A technician should be called if replacing the probe and cleaning the socket do not resolve the fault, as the issue may be in the wiring harness or control board.
Can I still use my KitchenAid range if F4 E0 is showing?
You can typically still use the range for standard baking and broiling functions since F4 E0 is specific to the meat probe circuit. The probe-assisted cooking feature will not function correctly while this fault is active. Avoid using the temperature probe function until the fault is resolved, as inaccurate readings could lead to undercooked food.
How much does it cost to fix F4 E0 on a KitchenAid range?
A replacement KitchenAid meat probe typically costs between $20 and $50 depending on the model, and installing it requires no tools. If the probe socket needs replacement, parts usually run $30 to $80 and the repair involves some disassembly, which is manageable for a confident DIYer. A control board or wiring harness repair done by a technician could cost $200 to $400 or more including labor.
Will F4 E0 clear on its own after I replace the meat probe?
In most cases, the error clears automatically once the faulty probe is removed or replaced and the range is powered back on. If the code persists after installing a new probe, the fault lies elsewhere in the circuit, such as the probe socket or wiring, and further diagnosis is needed. A power cycle by unplugging the range for one minute can help confirm whether the new probe resolved the issue.

Related KitchenAid range codes

All KitchenAid range codes
View all 79 KitchenAid range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass