Skip to main content
Error code reference
KitchenAid Range Error Codes
80 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
DOOR LOCKEDOven door is locked during or after self-cleaning cycle due to high temperature.ErrAn invalid control pad was pressed on the electronic oven control.FThe oven control has detected a fault or error condition (any F error displayed).F01Temperature sensor openedF02Welded element relaysF03EEPROM error on the electronic range control.F04Communication error between main electronic control and secondary oven electronic…F05Door or latch problemsF06Electronic range control malfunction.F07Encoder Failure.F08Cancel Button Disconnected.F0E0No error(s) foundF1Bake/Clean temperature runaway alarmF1 E5Sensor usage out of range (internal error).F1 E7PCB thermistor/sensor open or shorted.F1 E8Improper keypad feedback from power board supply lift.F1 EAExceeded stack warning level.F1-E1EEPROM checksum does not match at start key (silent fault, not displayed).F1-E4Internal error (display board related).F1-E6Internal error (power board related).F1-E9Internal error (display board related).F1E0Internal failure-oven user interface requires replacement.F1E2Internal board failure (A/D error) on LCC 180/190 control.F1E3Configuration jumper changeF2Open temperature sensorF2 E0User is cleaning too long or keypad is disconnected.F2 E1Keypad disconnect or keypad disconnected.F2 E3Key held down too long or keyboard short or spill on switch surface; needs surface…F2 E4Keys unsettled, probably due to noise.F20Water temperature out of range in the steam boiler system.F21Water Level Sensor Error (display LED indicates which sensor probe is not working).F23Boil over temperature condition in the steam boiler.F24Drain button disconnected from the steam board.F25Boiler failureF2E2Cancel key loop test failed.F2E5Cancel key failed.F3Shorted temperature sensorF3 E5Bottom oven sensor shorted (lower/bottom oven sensor shorted).F3E0Main oven temperature sensor open (top oven sensor opened).F3E1Lower main oven sensor shorted or open (range not equipped with this feature).F3E2Warming drawer sensor shorted (range not equipped with this feature).F3E3CLEAN range over temperature (LCC 180/190).F3E4Bottom oven temperature sensor open (bottom oven sensor open).F3E6Warming drawer temperature sensor open.F3E7Warming drawer temperature sensor shorted.F4Meat probe failure.F4 E0Meat probe shorted (less than 1500 ohms).F4-E1Meat probe shorted (less than 1500 ohms).F4E2Over temperature during cook mode (temperature runaway error).F4E3Over temperature during clean mode (temperature runaway error).F4E7Over temperature in oven cavity 2 (temperature runaway error).F5Element relay enable onF5 E4Latch switch fault.F5 E7Door unlocked but will not unlatch after clean cycle.F5-E3Loss of 120 VAC across L1 to ground, or Q19 circuit error (non-polarized receptacle).F5-E5Self-clean temperature not satisfied after 30 minutes.F5E0Door and door position switches do not agree during Clean mode (LCC 180/190).F5E1Door latch not operating during Clean mode (LCC 180/190).F5E2Door and door position switches do not agree during Clean mode (LCC 180/190).F5E6Door locked somehow with door open.F6 E1Over temperature during cook mode (runaway temp).F6 E2Over temperature during clean mode (runaway temp).F6 E5No cavity size command-control has not been programmed with oven cavity size.F6-E4Lost communication between display board and power board.F6E0Lost communication between user interface and appliance manager.F6E3Mini oven/warm drawer over temperature (range not equipped with this feature).F7Input switches failure in all modes except clean (door switch or door latch switch).F7 E1Invalid door switch reading.F7-E0Input switches will not follow their strobe level (shorted to ground).F8E0Blower low speed too low.F8E2Blower high speed too low.F9Miswired house or miswired range (LCC 90/95).F9E0Miswired house or miswired cooker power supply.Letter followed by a numberAn error/fault code is displayed indicating a malfunction.LOCControl Lock is active; the control panel pads are shut down to prevent unintended use of…LOCKEDOven temperature is too high after self-cleaning; door remains locked until oven cools.PFPower failure has occurred; display shows PF when power is first supplied or after a…PF id=27Power failure variant displayed on some models.PF id=30Power failure variant displayed on some models.SET CLOCKA power failure has occurred and the clock needs to be reset.
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for unlimited access to all brands and Max AI diagnostics.
More KitchenAid error codes
Common questions
How do I find the error code on my KitchenAid Range?
Most KitchenAid ranges show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.
Are these codes specific to my model?
The codes here apply broadly to KitchenAid ranges. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.
What do I do if my code is not listed?
Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.
How much does it cost to access the full diagnostic procedures?
A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.