mypros+
Error code reference

KitchenAid Range Error Code F1E0

Internal failure

KitchenAid codesKitchenAid range codes

Internal failure – oven user interface requires replacement.

First step from the service manual

Unplug range or disconnect power, then replace the user interface.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F1E0.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F1E0 means on a KitchenAid range

F1E0 is an EEPROM read fault on the KitchenAid range control board. The EEPROM (Electrically Erasable Programmable Read-Only Memory) is a small memory chip embedded in the control board that stores calibration data, user settings, and operational parameters. When the control board's processor attempts to read from this chip and receives corrupted or no data, it logs F1E0 internally. This is classified as a silent fault, meaning it does not display on the range's user interface under normal operation. The control board itself is both the component that detects the fault and the component that contains the failed EEPROM.

For homeowners, this means the brain of your range has detected a memory error inside its own circuit board. The EEPROM chip holds settings that tell the control board how to operate correctly. When this memory fails or becomes unreadable, the board cannot reliably reference its stored data, which can cause unpredictable behavior or hidden operational issues even if nothing appears wrong on the display.

Because F1E0 points directly to an internal failure of the control board's memory chip, the EEPROM is not a separately replaceable component on these units. The manufacturer's first troubleshooting step is to replace the entire control board assembly. No external wiring, sensors, or user-serviceable components are involved in this fault.

Source: manufacturer service documentation.

Common causes of F1E0

  1. 01

    Failed EEPROM chip on the control board

    Part replacement

    The EEPROM chip on the control board has degraded or failed internally, preventing the processor from reading stored data. This is the direct cause of F1E0 and the most likely scenario, as the fault definition points specifically to an EEPROM read failure.

  2. 02

    Corrupted EEPROM data from power surge

    Part replacement

    A voltage spike or power surge can corrupt the data stored on the EEPROM without physically destroying the chip. Once corrupted, the control board logs F1E0 because the data it reads back does not pass internal validation checks.

  3. 03

    Control board communication fault between processor and EEPROM

    Part replacement

    An internal trace or solder joint failure on the control board can interrupt communication between the main processor and the EEPROM chip, triggering a read fault even if the EEPROM chip itself is intact. The result is the same from a diagnostic standpoint, and full board replacement is still required.

See the test procedure for each cause

Frequently asked questions about F1E0

What does F1E0 mean on a KitchenAid range?
F1E0 indicates an EEPROM read fault on the KitchenAid range control board. The EEPROM is a memory chip built into the control board that stores operational settings and calibration data. When the board's processor cannot successfully read from this chip, it logs F1E0. This fault is silent and does not appear on the display under normal conditions, so it is typically discovered during a service diagnostic scan.
How do I fix F1E0 on a KitchenAid range?
The manufacturer's specified fix for F1E0 is replacing the control board. The EEPROM is not a separately serviceable component on these ranges, so board-level repair is not a standard option. You will need the model number from the range's rating plate to order the correct replacement control board. If you are comfortable working with appliance electronics and disconnecting wire harnesses, this is a DIY-feasible repair, though a qualified technician can complete it if you prefer.
Is it safe to use my KitchenAid range when F1E0 is active?
F1E0 is a silent fault stored internally and does not immediately disable the range or indicate a safety hazard like a gas leak or electrical short. However, an EEPROM read fault means the control board may not be reliably referencing its stored calibration and operational data, which can lead to unpredictable behavior over time. Using the range for occasional, attended cooking while awaiting a repair is a low-risk decision, but leaving it unattended or relying on it for precise temperature-sensitive cooking is not advisable until the control board is replaced.
How much does it cost to fix F1E0 on a KitchenAid range?
A replacement KitchenAid range control board typically costs between $150 and $400 depending on the specific model, with prices varying by retailer. If you hire a technician, expect to add $100 to $200 in labor for the diagnosis and board swap. DIY replacement is feasible for someone comfortable with basic appliance repair since the job primarily involves disconnecting wire harnesses and swapping the board, which usually takes under an hour.
Why does F1E0 on my KitchenAid range not show on the display?
F1E0 is classified as a silent fault, meaning the control board logs it internally but does not push it to the user display under normal operation. KitchenAid designs certain fault codes to operate this way when the issue does not immediately prevent the appliance from running. The fault is retrieved through a service diagnostic mode, which is why many owners discover F1E0 only during a technician visit or when using a diagnostic tool to pull stored error codes.

Related KitchenAid range codes

All KitchenAid range codes
View all 79 KitchenAid range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass