Skip to main content
Error code reference
KitchenAid Oven Error Codes
103 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
E0Temperature sensor opened.E1Temperature sensor shorted.E2Meat probe shorted.E3Self-clean latch will not lock.E3 or E64Electronic control malfunction.E5Self-clean latch will not unlockF0Default F codeF0 E3Electronic control malfunction.F0 E4Electronic control malfunction.F01Probe error-the reading of the ohm value of the temperature probe is out of range (value…F02Temperature error-if door is unlocked, temperature over threshold 1 (2150Ω) for at least…F03Configuration data set error-the data contained in the Configuration part of the memory…F04Communication error-occurs when other WIDE nodes are connected to the BUS; max number…F08UI EEPROM error-wrong EEPROM data access in writing and reading operation; data contained…F09UI SPI memory error-data contained in the SPI memory are not consistent (CRC mismatch)…F0E0No failure (GOOD)F1Wiring harness cavity size does not match previously stored value; the Cavity Size Select…F1 (All Other E Codes)Electronic control malfunction (when the E code is not E3).F1-E9Stack overflow (Electronics Subsystem Failure).F10User Interface communication or internal failure.F103Board or Heat Sink over temperature-board or heat sink NTC reads over 100°C.F104Coil 1/2 Over Temperature.F11Current/Voltage/6th Sense error-current out of range for 5 seconds (>19A for 16A oven…F14Meat Probe error-value read is out of range (lower than 0°C or greater than 120°C) for 30…F17Meat Probe error-value read out of allowed range (<0°C or >120°C) for 30 seconds; checked…F1E0Internal failureF1E1Check oven appliance managerF1E2Check microwave oven user interfaceF1E3Configuration jumper change; freestand, electric switches or P9 pins 6 to 7 changed since…F1E4Check microwave oven power relayF1E5Check microwave oven inverterF2Keyboard/keypad shorted, Cancel not operating (Keypad Subsystem Failure).F2-E3Electronic control malfunction-keypad keytail not connected.F2-E4Keypads unsettled (applies to capacitive glass when a constant reading cannot be taken).F2-E5Electronic control malfunction-keypad keytail not connected.F2-E6CANCEL key drive line open (associated with E5/E6 group).F20Keypad failure.F21Keypad failure.F2E0Keypad disconnectedF2E1Stuck key or shorted key detected on the keypad.F2E2Cancel key loop test failed.F3Wiring harness cavity size does not match the previously stored value (cavity size select…F3 E3Oven temperature too high (over 510°C / 950°F in Clean mode).F3-E0Temperature sensor opened-R=2875 ohm (by spec).F30Upper oven temperature sensor open or shorted.F31Lower oven temperature sensor open or shorted.F33Meat Probe Jack or Meat Probe failure.F34Coil 1/2 Under Current-the current averaged every half period is less than 3 Ampere for…F3E1Lower main oven sensor shorted or openF3E2Warming drawer sensor shorted or openF4Oven temperature too high-oven cavity temperature must have exceeded a safe level, or…F4-E0Temperature sensor (lower) opened.F4-E3Temperature sensor (microwave) shorted.F43Main Frequency Wrong-wrong frequency detected (out of 50Hz ±5%) for more than 5 seconds.F46Main Relay Stuck-the main relay is detected as stuck.F47Fan blocked-fan frequency is out of range (10-120Hz) for at least 5 seconds; if lower…F48Wrong Vref/2 value-the sampled Vref_2 is different from 2.5V for 12 seconds.F4E1Convection thermistor failure in the microwave oven.F4E2Microwave internal temperature sensor (ambient sensor on MW appliance manager) failure.F4E4Humidity sensor failure in the microwave oven.F5Self clean latch will not lock, oven did not reach self clean temp after 30 minutes, door…F5-E0Door is open, but latch is locked (door switch closed indicating open door, and latch…F5-E5Self-clean temperature set point is not reached within the required time range (usually…F50LOGIC circuit failure for upper oven (door latch related).F51Upper oven door latch LOGIC circuit failure (latch did not lock or unlock properly).F53Mains Zero Crossing missing-no mains zero crossing signal detected.F54Lower oven door latch LOGIC circuit failure (latch did not lock or unlock properly).F55Heatsink NTC open or shorted-heat sink temperature is out of range (-40°C to 125°C) for…F56Board NTC open or shorted-board temperature is out of range (-10°C to 87°C) for at least…F58Coil 1/2 NTC shorted-coil NTC reads over 240°C for at least 1 second.F59Coil 1/2 NTC open-coil NTC reads under 16°C for at least 30 seconds.F5E1Door latch not operatingF5E2Warming drawer sensor shorted or open.F5E3Loss of 120 VAC across L1 to Ground or Q19 circuit error.F5E6Door locked somehow with door open.F5E7Door unlocked somehow and will not unlatch.F6Switch pulse return line is not connected; electronic control will display F6 within 60…F6 E0Return line not connected; electronic control will display F6 within 60 seconds after…F6 E5No cavity size commandF6-E2Microwave cavity over temperature during cooking.F60User Interface and Appliance Manager communication failure.F61Upper oven heating element failure or oven sensor failureF63Lower oven heating element failure or oven sensor failureF64DC Link Over Voltage-DC link voltage is greater than limit for at least 30 seconds…F65DC Link Under Voltage-DC link voltage is lower than limit for at least 30 seconds…F66User Interface and Appliance Manager communication failure.F69WIDE communication error-communication between AEVO and IPC does not occur; appears if…F6E1Cook oven over temperature condition detected.F6E3Mini oven/warm drawer over temperatureF6E4User interface and appliance manager mismatchF7Common switch wire (+30VDC/5Hz) to latch switch and door switch is shorted to chassis…F7E0Input switches won't follow their strobe level (shorted to ground).F8Oven door is open but latch is locked.F8-E0Self-clean latch will not unlock.F8-E1Oven over temperature while door open and latch lock.F8-E2Oven over temperature while door open and latch unlock.F8-E3Oven over temperature while door close and latch unlock.F8-E4Oven over temperature while door close and latch unlock.F80EPROM Configuration Error-the data contained in the Configuration part of the memory are…F9Oven door latch will not unlock, or common wire (+5Vdc) to latch switch and door switch…F94IO Port Error-the data read from microcontroller during the IO port check is not…PFPower FailureSABOven is in Sabbath Mode.
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for unlimited access to all brands and Max AI diagnostics.
More KitchenAid error codes
Common questions
How do I find the error code on my KitchenAid Oven?
Most KitchenAid ovens show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.
Are these codes specific to my model?
The codes here apply broadly to KitchenAid ovens. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.
What do I do if my code is not listed?
Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.
How much does it cost to access the full diagnostic procedures?
A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.