mypros+
Error code reference

KitchenAid Oven Error Code F11

Current/Voltage/6th Sense error

KitchenAid codesKitchenAid oven codes

Current/Voltage/6th Sense error – current out of range for 5 seconds (>19A for 16A oven, >15A for 13A oven, >12A for 10A oven); voltage out of range (<200V or >260V) for 30 seconds; or communication between micro and 6th sense chip lost for 30 seconds.

First step from the service manual

Failure is erased when the oven goes OFF (current), voltage returns to range for 30 seconds, or communication returns.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F11.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F11 means on a KitchenAid oven

The F11 error code on a KitchenAid oven signals a Current/Voltage/6th Sense fault, and it can be triggered by one of three distinct conditions. First, the oven's current draw exceeds safe thresholds for a sustained 5-second period: more than 19 amps on a 16A-rated unit, more than 15 amps on a 13A unit, or more than 12 amps on a 10A unit. Second, the incoming supply voltage falls below 200V or rises above 260V for 30 continuous seconds. Third, communication between the main microcontroller and the 6th Sense chip is lost for 30 seconds.

The 6th Sense system is an intelligent load-monitoring circuit that regulates cooking performance by tracking current and communicating that data to the main control board. When current spikes beyond the rated threshold, it typically points to a shorted heating element, a failing relay on the control board, or a wiring fault drawing excessive load. Voltage faults are almost always caused by problems at the home's electrical supply, such as a weak circuit breaker, a loose connection at the terminal block, or utility-side voltage irregularities. Communication faults between the micro and 6th Sense chip generally indicate a defective control board or corrupted firmware.

This error is self-clearing under specific conditions. A current overload fault clears automatically when the oven is turned off. A voltage fault clears once the supply voltage returns within the 200V to 260V window for 30 consecutive seconds. A communication fault clears when normal data exchange between the microcontroller and 6th Sense chip resumes. Because the code can clear on its own, recurring appearances are more diagnostically significant than a single isolated occurrence.

Source: manufacturer service documentation.

Common causes of F11

  1. 01

    Shorted or failing heating element

    Part replacement

    A bake or broil element drawing excessive current can push amperage beyond the oven's rated threshold within seconds. Inspect elements for visible burn marks, blistering, or breaks, and test resistance with a multimeter to confirm a short to ground.

  2. 02

    Low or unstable supply voltage

    Wiring / connection

    If the incoming voltage drops below 200V or surges above 260V for 30 seconds, F11 will trigger. Check the voltage at the terminal block with a multimeter while the oven is running to confirm whether the issue originates at the home's circuit breaker, wiring, or utility supply.

  3. 03

    Faulty main control board

    Part replacement

    A defective relay on the control board can cause uncontrolled current flow to a heating circuit, or the board's microcontroller may lose communication with the 6th Sense chip due to component failure or corrupted firmware. If element and voltage checks are normal, the control board is the likely culprit.

  4. 04

    Loose or damaged wiring connections

    Wiring / connection

    Corroded, loose, or heat-damaged wire connections at the terminal block, control board connectors, or element terminals can cause both abnormal current readings and intermittent communication faults. Inspect all high-voltage connections for discoloration, melting, or looseness.

  5. 05

    Tripped or weak circuit breaker

    Part replacement

    A circuit breaker that is failing to hold its rating can cause voltage at the oven to sag below 200V under load, triggering the voltage fault condition. Reset the breaker and monitor voltage under load, replacing the breaker if voltage is unstable.

See the test procedure for each cause

Frequently asked questions about F11

What does F11 mean on a KitchenAid oven?
F11 indicates a Current, Voltage, or 6th Sense fault. It triggers when the oven draws too much current for its rating (sustained for 5 seconds), when supply voltage falls outside the 200V to 260V range for 30 seconds, or when the main microcontroller loses communication with the 6th Sense chip for 30 seconds. The 6th Sense system monitors electrical load to optimize cooking performance, so a fault here can affect both safety and function.
Will resetting the oven clear the F11 error code?
The F11 code is self-clearing under specific conditions without a manual reset. A current fault clears when the oven is turned off, a voltage fault clears when supply voltage returns to normal for 30 seconds, and a communication fault clears when the microcontroller and 6th Sense chip resume normal data exchange. However, if the underlying problem persists, the code will return. A single occurrence may not indicate a serious issue, but repeated faults require hands-on diagnosis.
Is it safe to use my KitchenAid oven when F11 is displayed?
You should not continue using the oven until the cause is identified, especially if the error recurs. Overcurrent conditions can indicate a shorted heating element or a failing relay, both of which pose a risk of further electrical damage or fire. A voltage fault from the home's electrical supply may also affect other appliances on the circuit. Treat a recurring F11 as a reason to keep the oven off until it is inspected.
How do I fix the F11 error on a KitchenAid oven?
Start by checking the supply voltage at the terminal block with a multimeter to confirm it stays between 200V and 260V under load. Next, inspect the bake and broil elements visually for burns or damage, and test them with a multimeter for shorts. If elements and voltage are normal, examine all wiring connections for looseness or heat damage. If none of those checks reveal the problem, the main control board is likely at fault and will need to be replaced.
How much does it cost to repair a KitchenAid oven showing F11?
Repair costs depend on the root cause. A replacement heating element typically costs between $20 and $80 for the part, with labor adding $75 to $150 if a technician is called. A new control board is more expensive, generally ranging from $150 to $350 for the part alone. If the fault is caused by a weak circuit breaker or home wiring issue, an electrician visit may cost $100 to $250. Diagnosing the specific cause first will prevent paying to replace parts that are not actually defective.

Related KitchenAid oven codes

All KitchenAid oven codes
View all 102 KitchenAid oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass