mypros+
Error code reference

KitchenAid Oven Error Code F08

UI EEPROM error

KitchenAid codesKitchenAid oven codes

UI EEPROM error – wrong EEPROM data access in writing and reading operation; data contained in memory are not consistent (CRC calculated by SW is not equal to value stored in memory).

MyPros+ Max

Get the full diagnostic procedure for F08.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F08 means on a KitchenAid oven

The F08 error code on a KitchenAid oven indicates a User Interface (UI) EEPROM fault. EEPROM stands for Electrically Erasable Programmable Read-Only Memory, which is the non-volatile memory chip embedded in the UI control board that stores critical configuration data, calibration settings, and operational parameters. The error is triggered when the software performs a cyclic redundancy check (CRC) on the data stored in memory and finds that the calculated CRC value does not match the checksum stored in the EEPROM. This mismatch signals that the data in memory has become corrupted, incomplete, or inconsistent.

This type of fault typically originates in the UI control board itself. The EEPROM chip can develop read/write errors due to age-related degradation of the memory cells, voltage spikes or power surges that corrupt stored data, or failures within the control board's circuitry that handles memory access operations. In some cases, a momentary power interruption during a write cycle can leave the memory in an incomplete state, causing the CRC check to fail on subsequent power-up.

Because the error specifically references both writing and reading operation failures, the root cause is almost always in the UI control board assembly rather than in external wiring or sensors. A power reset will sometimes clear a transient CRC mismatch caused by a brief power anomaly, but a persistent F08 code generally indicates the EEPROM or the surrounding board circuitry has failed and the UI control board requires replacement.

Source: manufacturer service documentation.

Common causes of F08

  1. 01

    Failed or corrupted UI control board EEPROM

    Part replacement

    The memory chip on the UI control board has developed a permanent read/write error or its stored data has become corrupted beyond recovery. This is the most common cause of a persistent F08 error and typically requires replacing the UI control board assembly.

  2. 02

    Power surge or voltage spike

    Wiring / connection

    A sudden surge in line voltage can corrupt the data stored in EEPROM during a write cycle, causing a CRC mismatch on the next power-up. If the surge was isolated and the board is otherwise intact, a power reset may clear the fault.

  3. 03

    Interrupted write cycle due to power outage

    Wiring / connection

    If power was lost while the control board was writing data to EEPROM, the stored data can be left in an incomplete state, causing the CRC check to fail. A full power reset by disconnecting the oven from the power supply for several minutes may resolve this.

  4. 04

    Age-related EEPROM cell degradation

    Part replacement

    EEPROM memory cells have a finite number of read/write cycles. On older ovens, the memory cells can degrade to the point where data can no longer be reliably stored or retrieved, resulting in a persistent F08 fault that does not clear with a reset.

  5. 05

    Internal UI control board circuitry failure

    Part replacement

    Failures in the control board components that manage memory access, such as the microcontroller or supporting circuitry, can cause incorrect read/write operations that produce a CRC mismatch. This type of fault requires full UI control board replacement.

See the test procedure for each cause

Frequently asked questions about F08

What does F08 mean on a KitchenAid oven?
F08 indicates a User Interface EEPROM error, meaning the control board's internal memory chip has encountered a data inconsistency. The software performs a cyclic redundancy check (CRC) on the stored data and found that the calculated value does not match what is stored in memory. This points to corrupted, incomplete, or unreadable data within the UI control board's memory.
Will resetting my KitchenAid oven clear the F08 error?
A power reset can clear the F08 error if it was caused by a transient event such as a brief power outage or a momentary voltage fluctuation during a memory write cycle. To reset, disconnect the oven from power at the breaker or by unplugging it for at least 5 minutes, then restore power. If the F08 code returns immediately or shortly after the reset, the EEPROM or UI control board has a permanent fault and will need to be replaced.
Is it safe to use my KitchenAid oven when F08 is displayed?
An F08 error indicates a failure in the UI control board's memory, which means the oven's control system may not be operating reliably. It is generally not recommended to continue using the oven while this fault is active, as the corrupted control data could lead to unpredictable behavior. Discontinue use until the fault is diagnosed and resolved.
How much does it cost to fix a KitchenAid oven F08 error?
If a power reset does not clear the code, the repair typically involves replacing the UI control board assembly. Parts costs for a replacement UI control board generally range from $150 to $350 depending on the specific model, and professional labor to diagnose and install the board can add $100 to $200 to the total repair cost. Costs can vary based on your location and the technician's rates.
Can I replace the KitchenAid oven UI control board myself?
A knowledgeable DIYer with experience in appliance repair can replace the UI control board on many KitchenAid oven models, as the job typically involves disconnecting wiring harnesses and removing mounting screws. However, working with oven electronics requires the oven to be fully disconnected from power before beginning any work. If you are not confident in safely handling appliance electrical components, it is best to have a qualified technician perform the repair.

Related KitchenAid oven codes

All KitchenAid oven codes
View all 102 KitchenAid oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass