Model reference

KitchenAid KFGC500JPA05

Range

4 documents48 error codes14 service modes

Available documentation

Tech Sheet

Tech Sheet - W11565467 - Rev A2 pg
Covers this model

Service Manual

Tech Manual39 pg
Covers this model

Service Flash

Service Pointer - W11643965 - Rev A - Slow_No Ignition Commercial Range_Cooktop_W1164396512 pg
Covers this model

Installation Guide

Installation Instructions88 pg
Covers this model

MyPros+ Max

Diagnose your KitchenAid KFGC500JPA05.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·KitchenAid Range

F1 E0 on my KitchenAid KFGC500JPA05

M+

Oven user interface failure.

From Tech Sheet W15465189, p.41:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (48)

CodeMeaning

F1 E0Oven user interface failure.F1 E1Internal Oven Appliance Manager (AM) error.F1E0User Interface Board F1E1Control Relay Board F2 E0Keypad disconnected.F2 E1Stuck or shorted key on keypad.F2E0Keypad disconnected.F2E1Stuck Key F2E2Oven Knob F3 E0Main oven temperature sensor open or shorted.F3 E1Bottom oven temperature sensor open or shorted.F3 E3Meat probe connector jack or meat probe shorted.F3E0Main Oven Sensor Open or Shorted.F3E1Main Oven Meat Probe Short-Circuit.F3E3Main Oven Door Latch Switch error.F3E9Left Oven Meat Probe Short-Circuit.F5 E0Door and latch switch do not agree (main/upper oven).F5 E1Latch not operating (main/upper oven).F5 E3Door and latch switch do not agree (lower oven).F5 E4Latch not operating (lower oven).F5E0Main Oven Door Latch Switch error.F5E1Main Oven Door Latch Motor error.F5E3Left Oven Door Latch Switch error.F5E4Left Oven Door Latch Motor error.F6 E0Oven user interface lost communication.F6 E1Over temperature (main/upper oven).F6 E3Over temperature (lower oven).F6 E4User Interface / Appliance Manager state status mismatch.F6 E6Oven appliance manager lost communication (main/upper oven).F6 E9Oven appliance manager lost communication (lower oven).

View all 48 error codes

F6 EAUser Interface over temperature.F6E0User Interface Connection error.F6E1Main Oven Over Temperature Limit exceeded.F6E3Left Oven Over Temperature Limit exceeded.F6E4Control Status error.F6E6Main Oven Control Connection error.F6E9Left Oven Control Connection error.F6EAUser Interface over temperature.F8 E0Low fan speed underspeed.F8 E1Low fan speed overspeed.F8 E2High fan speed underspeed.F8 E3High fan speed overspeed.F8E0Main Oven Cooling Fan speed low or not functioning.F8E1Left Oven Cooling Fan Speed Low.F8E2Main Oven Cooling Fan Speed High.F8E3Left Oven Cooling Fan Speed High.F9 E0Product not wired correctly (neutral connection may be switched with L1 or L2).F9E0Power Input

Service modes (14)

Cavity Size Select1
cavity_size_select1
diagnosticPress CANCEL > CANCEL > START on the control panel.
Diagnostics modePress CANCEL > CANCEL > START
Error Codes (Fault History)1
error_codes_view1
Fault Code DisplayWhile in Diagnostics Mode, rotate the Mode Selector knob clockwise until Fault Code Display is…
Manual DiagnosticWhile in Diagnostics Mode, rotate the Mode Selector knob clockwise until Manual Diagnostic is…
Relay Activation1
relay_activation1
Service Diagnostic Mode Entry1. Start with knobs in initial position
Software VersionFor Engineering only
Status Screen1
status_screen1

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass