mypros+
Model reference

KitchenAid KGST300HBL6

Range

10 documents33 error codes20 service modes

Available documentation

Tech Sheet

  • Whirlpool Oven YKGRT607HS6 Tech Sheet8 pg
    Covers this model
  • Wiring Sheet - 97543721 pg
    Covers this model
  • TECH SHEET - 9754241 - Rev A8 pg
    Covers this model
  • Tech Sheet 9754241 KGRT607HBS6 KA Range8 pg
    Covers this model

Service Manual

  • KitchenAid Electronic Range Controls "B" & "D" Line Wall Ovens Job Aid93 pg
    Covers this model

Service Flash

  • Service Pointer - Error Code F1 E3 appears after servicing the range4 pg
    Covers this model

Installation Guide

  • Installation Instructions7 pg
    Covers this model
  • Instruction Sheet2 pg
    Covers this model
  • Instruction Sheet1 pg
    Covers this model

Other

  • 431716993 pg
    Covers this model
MyPros+ Max

Diagnose your KitchenAid KGST300HBL6.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (33)

CodeMeaning
F0 E0No fault found.F1 E0EEPROM read fault (silent fault, not displayed).F1 E1EEPROM checksum does not match at start key (silent fault, not displayed).F1 E2Lost communication with power board.F1 E3Configuration jumper change; freestand, electric switches or P3 pins 1 to 5…F1 E4Oven sensor not calibrated.F1 E5Meat probe not calibrated.F1 E6Display board EPROM access failure.F1 E7Power board EPROM access failure.F1 E8Improper keypad feedback (power board supply lift).F1 E9Unstable keyboard gain.F1 EAExceeded stack warning level.F2 E0User is cleaning too long or keypad is disconnected.F2 E1Cancel key invalid.F2 E2Cancel key loop test failed.F2 E3Key held down too long or keyboard short or spill on switch surface.F2 E4Keys unsettled, probably due to noise.F3 E0Oven sensor open circuit.F3 E1Oven temperature sensor (PLAT sensor) shorted.F3 E2Oven temperature too high (runaway).F3 E3Shorted oven sensor.F3 E4Oven temperature too high (runaway condition).F4 E0Meat probe shorted (less than 1500 ohms).F4 E1Meat probe shorted (less than 1500 ohms).F5 E1Self clean latch not locking.F5 E3Loss of 120 VAC across L1 to ground, or Q19 circuit error.F5 E5Self clean temperature not achieved after 30 minutes.F5 E6Door locked with door open.F5 E7Door unlocked but will not unlatch after clean cycle.F6 E0Ambient sensor opened (too hot).
View all 33 error codes
F7 E0Invalid latch switch reading.F7 E1Invalid door switch reading.PFPower failure indication (not a failure mode).

Service modes (20)

  • Convection Freestanding/Slide-In Control ProgrammingAfter unit is powered up, press the following keypad sequence
  • End of Service Test Sequence (Convection Units)["Connect unit to power, set power ON and wait until CONTROL LOCK clears and display shows PF…
  • End of Service Test Sequence (Non-Convection Units)["Connect unit to power, set power ON and wait until CONTROL LOCK clears and display shows PF…
  • F1 E3 Configuration Reset (Convection Units)["Ensure harness to P1 connector is correctly installed per wiring diagram.","Power off and wait 5…
  • F1 E3 Configuration Reset (Non-Convection Units)["Ensure harness to P1 connector is correctly installed per wiring diagram.","Power off and wait 5…
  • Hidden Functions - Bake Temperature CalibrationTouch and hold the Bake keypad for 5 seconds.
  • Hidden Functions - Clock Display OffTouch and hold the Clock keypad for 5 seconds.
  • Hidden Functions - DehydrateTouch and hold the Conv
  • Hidden Functions - End-of-Cycle Tones OffTouch and hold the Cook Time keypad for 5 seconds.
  • Hidden Functions - Fahrenheit/Celsius ToggleTouch and hold the Broil keypad for 5 seconds.
  • Hidden Functions - Keypad Entry Tones OffTouch and hold the Stop Time keypad for 5 seconds.
  • Hidden Functions - Keypad LockoutTouch and hold the #3 keypad for 5 seconds.
  • Hidden Functions - Last F/E Code and ROM RevisionTouch and hold the #0 keypad for 5 seconds.
  • Hidden Functions - Raising Bread DoughTouch and hold the Baked Goods keypad for 5 seconds.
  • Hidden Functions - Range Configuration DisplayTouch and hold the #1 keypad for 5 seconds.
  • Hidden Functions - Sell ModeTouch and hold the Timer Cancel keypad for 5 seconds.
  • Hidden Functions - Timer Operating Tones OffTouch and hold the Timer Start keypad for 5 seconds.
  • Hidden Functions - Tone Frequency ChangeTouch and hold the #7 keypad for 5 seconds.
  • Non-Convection Freestanding/Slide-In Control ProgrammingAfter unit is powered up, press the following keypad sequence
  • Sabbath Mode1

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass