Model reference
KitchenAid KGST307BBL1
Range
11 documents72 error codes21 service modes
Available documentation
Tech Sheet
- Wiring Sheet - 9751761 - Rev E1 pg
- TECH SHEET - KitchenAid Range KGST307BBL28 pg
- TECH SHEET8 pg
Service Manual
- Whirlpool KAC 22 Failure Codes Wiring Diagrams for Freestanding Slide in Ranges and Built in Ovens34 pg
- kac-22-whrlpl34 pg
- kitchenaid-failure32 pg
- Job Aid - 4317266 (KAC-22)33 pg
- Electronic Oven Controls - Job Aid 431726633 pg
- KitchenAid Electronic Range Controls "B" & "D" Line Wall Ovens Job Aid93 pg
Other
- Kitchenaid Range KGST307BBL2 Wiring Sheet 97526681 pg
- 431716993 pg
MyPros+ Max
Diagnose your KitchenAid KGST307BBL1.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (72)
CodeMeaning
F1Control out of calibrationF1 E0EEPROM read fault (silent fault, not displayed).F1 E1EEPROM checksum does not match at start key (silent fault, not displayed).F1 E3Configuration jumper changeF1 E4Q8 shorted.F1 E9Stack overflow, highest priority fault.F1-E0Electronics subsystem failureF1-E1Electronics subsystem failureF1-E2Electronics subsystem failureF1-E3Electronics subsystem failureF1-E5Electronics subsystem failureF1-E9Electronics subsystem failureF1E0EEPROM read fault (silent fault, not displayed).F1E1EEPROM checksum does not match at start key (silent fault, not displayed).F1E3Configuration jumper change; freestanding, electric switches or P9 pins 6 to 7…F1E4Q8 shorted.F1E9Stack overflow, highest priority.F2Keyboard shorted, Cancel not operating.F2 E0Cancel key level too low (open).F2 E2Cancel key loop test failed.F2 E3Key held down too long or keyboard short.F2 E4Keys unsettled, probably due to noise.F2-E0Keypad subsystem failureF2-E1Keypad subsystem failureF2-E4Keypad subsystem failureF2-E5Keypad subsystem failureF2E0Cancel key level too low (open).F2E2Cancel key loop test failed.F2E3Key held down too long or keyboard short.F2E4Keys unsettled probably due to noise.View all 72 error codes
F3Oven probe shorted or open.F3 E0Oven temperature sensor (PLAT sensor) open.F3 E1Oven temperature sensor (PLAT sensor) shorted.F3 E2Oven temperature too high (runaway).F3-E0Cavity temperature sensor failureF3-E1Cavity temperature sensor failureF3-E2Cavity temperature sensor failureF3-E3Cavity temperature sensor failureF3E0Oven sensor open.F3E1Shorted oven sensor.F3E2Oven temp too high (runaway).F4Meat probe shorted.F4 E1Meat probe shorted (less than 1500 ohms).F4-E1Meat probe failureF4E1Meat probe shorted (less than 1500 ohms).F5Door signal inconsistent.F5 E1Self-clean latch will not make after 30 seconds.F5 E3Loss of 120 VAC across L1 to ground, or Q19 circuit error.F5 E5Self-clean temperature not satisfied after 30 minutes.F5 E6Door locked with door open.F5 E7Door unlocked and will not unlatch.F5-E0Latch subsystem failureF5-E1Latch subsystem failureF5-E3Latch subsystem failureF5-E5Latch subsystem failureF5-E7Latch subsystem failureF5E1Self clean latch lock make after 30 seconds.F5E3Loss of 120 VAC across L1 to Ground or Q19 circuit error.F5E5Self clean temperature not satisfied after 30 minutes.F5E6Door locked somehow with door open.F5E7Door unlocked somehow and will not unlatch.F6Ambient (console bimetal) sensor open (too hot).F6 E0Ambient sensor opened (too hot).F6-E0Electronics over-temperatureF6-E1Electronics over-temperatureF6-E2Electronics over-temperatureF6E0Ambient (console bi-metal) sensor opened (too hot).F7Control or keypad switches shorted.F7 E0Input switches will not follow their strobe level (shorted to ground).F7-E0Digital switch signal (5 VDC @ 1kHz) failureF7E0Input switches won't follow their strobe level (shorted to ground).PFPower failure
Service modes (21)
- Convection Freestanding/Slide-In Control ProgrammingAfter unit is powered up, press the following keypad sequence
- F1E3 Configuration Reconfiguration ProcedureStep 1: Make sure harness to P1 connector is correct per wiring diagram. Step 2: Power down and…
- F1E3 Configuration Reset["Verify harness to P1 connector is correct per wiring diagram.","STEP 1
- Hidden Codes / Diagnostic AccessPress and hold each of the following pads for 5 seconds
- Hidden Codes / Diagnostic ModePress and hold each of the following keypads for 5 seconds to access hidden functions
- Hidden Functions - Bake Temperature CalibrationTouch and hold the Bake keypad for 5 seconds.
- Hidden Functions - Clock Display OffTouch and hold the Clock keypad for 5 seconds.
- Hidden Functions - DehydrateTouch and hold the Conv
- Hidden Functions - End-of-Cycle Tones OffTouch and hold the Cook Time keypad for 5 seconds.
- Hidden Functions - Fahrenheit/Celsius ToggleTouch and hold the Broil keypad for 5 seconds.
- Hidden Functions - Keypad Entry Tones OffTouch and hold the Stop Time keypad for 5 seconds.
- Hidden Functions - Keypad LockoutTouch and hold the #3 keypad for 5 seconds.
- Hidden Functions - Last F/E Code and ROM RevisionTouch and hold the #0 keypad for 5 seconds.
- Hidden Functions - Raising Bread DoughTouch and hold the Baked Goods keypad for 5 seconds.
- Hidden Functions - Range Configuration DisplayTouch and hold the #1 keypad for 5 seconds.
- Hidden Functions - Sell ModeTouch and hold the Timer Cancel keypad for 5 seconds.
- Hidden Functions - Timer Operating Tones OffTouch and hold the Timer Start keypad for 5 seconds.
- Hidden Functions - Tone Frequency ChangeTouch and hold the #7 keypad for 5 seconds.
- Non-Convection Freestanding/Slide-In Control ProgrammingAfter unit is powered up, press the following keypad sequence
- Sabbath Mode1
- Temperature Calibration1
Full entry steps, exit procedures, and test sequences are available in Max.
Related KitchenAid range models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass