mypros+
Model reference

KitchenAid YKER507XSS00

Range

5 documents48 error codes23 service modes

Available documentation

Tech Sheet

  • techsheet-w10340588-reva-fr.pdf24 pg
    Covers this model
  • Tech Sheet - W1034058716 pg
    Covers this model

Service Manual

  • Troubleshooting Gas and Electric Freestanding Range Electronic Controls70 pg
    Covers this model

Installation Guide

  • Installation Instructions20 pg
    Covers this model
  • Instruction Sheet1 pg
    Covers this model
MyPros+ Max

Diagnose your KitchenAid YKER507XSS00.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (48)

CodeMeaning
F1Control failure or UL A/D error(s) detected in the control board.F1 E*Control board failure (all F1 sub-codes indicate control fault).F1-E0EEPROM communication error (cooktop control).F1-E1Upper RTD uncalibrated (oven control).F1-E2Lower RTD uncalibrated (oven control).F1-E5Sensor usage out of range (oven control).F1-E7PCB Thermistor/Sensor open or shorted (oven control).F1-E9WIDE Queue full (cooktop control).F1E0Cooktop EEPROM communication error (internal).F1E1Upper RTD not calibrated (internal).F1E2Lower RTD not calibrated (internal).F1E5Sensor usage out of range (internal).F1E7Cooktop board sensor/thermistor open or short-circuited (PCB sensor).F1E9Cooktop WIDE queue full.F2Shorted/stuck key detected on the control keypad.F2-E0Keypad disconnected (oven control).F2-E1Stuck key (cooktop control).F2-E2Stuck key (oven control).F2E0Keypad disconnected.F2E1Stuck key.F2E2Stuck key.F3Oven sensor opened or oven sensor shorted.F3 E0Oven temperature sensor fault (open or shorted)F3 E1Lower oven temperature sensor fault (MRC II double oven models).F3 E2Warming drawer temperature sensor fault.F3-E0Main oven temperature sensor open or shorted (upper oven).F3-E1Main oven temperature sensor open or shorted (lower oven).F3E0Upper main temperature sensor open or short-circuited.F3E1Lower main temperature sensor open or short-circuited.F5 E0Door position switch fault
View all 48 error codes
F5 E1Door latch switch/system faultF5 E2Door switch fault.F5-E0Door and latch switches do not agree during Clean mode.F5-E1Door latch not operating during Clean mode.F5E0Mismatch between door switch and latch switch (clean mode).F5E1Door latch not functioning (clean mode).F6 E*Control communication failure.F6-E0Lost communications between controls.F6-E1Over temperature during cook mode (runaway temperature).F6-E2Over temperature during clean mode (runaway temperature).F6-E3Over temperature in warming drawer (runaway temperature).F6E0Loss of communications.F6E1Bake mode runaway temperature (excessive temperature during cooking).F6E2Clean mode runaway temperature (excessive temperature during self-clean).F6E3Warming drawer runaway temperature (excessive temperature).F9House miswiredF9-E0Product is mis-wired.F9E0Product miswired (incorrect wiring).

Service modes (23)

  • Cooktop Diagnostic ModePress 3 different keys in sequence, then repeat that same selected sequence two more times within…
  • Cooktop Diagnostics ModePress any 3 different keys in a sequence of 1, 2, 3 and then repeat this selected sequence 2 more…
  • Cooktop Fault Code Reading1
  • Erase All Error Codes (Oven)1
  • LCC Diagnostic Mode (LCC90/LCC95/LCC180)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • LCC190 Diagnostic Mode (Self Clean, Convection models)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME or TEMP/HOUR '+' key to cycle through…
  • MRC Diagnostic Mode["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC Diagnostic Mode (Fan/True Convection Electric - Oven Light entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC II Diagnostic Mode (Number 3 key entry - KitchenAid models)["Press OFF/OFF/START or CANCEL/CANCEL/START in sequence.","Press the number '3' key to cycle…
  • MRC II Diagnostic Mode (TEMP/TIME entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' keypad to cycle through diagnostic…
  • Oven Control Reset1
  • Oven Diagnostic ModePress CANCEL > CANCEL > START within 5 seconds.
  • Oven Diagnostics ModePress CANCEL > CANCEL > START within 5 seconds.
  • Oven Display Test1
  • Oven Fault Review1
  • Oven Manual Test Mode1
  • Oven Semi-Auto Test1
  • Oven Software Version1
  • Oven Usage Review1
  • Semi Automatic Test Mode (Oven)1
  • Temperature CalibrationPress SETTINGS/OPTIONS until 'Temp Calib' is displayed, then follow on-screen instructions.
  • Temperature Calibration AdjustmentPress SETTINGS/OPTIONS until 'Temp Calib' is highlighted, then follow instructions to see the…
  • Test Mode (Oven - Manual Relay Testing)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass