mypros+
Model reference

KitchenAid YKFEG500EBS3

Range

7 documents27 error codes19 service modes

Available documentation

Tech Sheet

  • Tech Manual16 pg
    Covers this model
  • Tech Sheet28 pg
    Covers this model
  • Tech Sheet W11401743 REVA2 pg
    Covers this model
  • Tech Sheet - W11401743 - Rev B2 pg
    Covers this model
  • Tech Sheet - W10694027 - Rev A (FR)8 pg
    Covers this model
  • W10694021A.fm8 pg
    Covers this model

Quick Reference

  • Freestanding Electric Range Control Guide20 pg
    Covers this model
MyPros+ Max

Diagnose your KitchenAid YKFEG500EBS3.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (27)

CodeMeaning
EEPROMEEPROM communication error.F1-E0EEPROM communication error.F1-E5Sensor out of range.F1-E7Circuit board thermistor open or short-circuited.F1-E9WIDE queue full.F1E0EEPROM communication error.F1E5Sensor out of range.F1E7PCB thermistor open or shorted.F1E9WIDE queue full.F2-E0Keypad disconnected.F2-E1Key stuck.F2-E2Cancel key error.F2E0Keypad disconnected.F2E1Stuck key.F2E2Cancel key error.F3-E0Main oven sensor open or short-circuited.F3-E2Warming drawer sensor open or short-circuited.F3E0Main oven temperature sensor open or shorted.F3E2Warming drawer sensor open or shorted.F5-E0Door and door switch mismatch (clean mode on some models).F5E0Door and door position switch do not agree (Clean mode, on some models).F6-E1Bake over-temperature condition.F6-E3Warming drawer over-temperature condition.F6E1Over temperature during cook mode.F6E3Over temperature in warming drawer.F9-E0Incorrect home or range wiring.F9E0Mis-wired house or range.

Service modes (19)

  • Auto Test1
  • CONTROL RESETFrom diagnostic mode, scroll to step 6 'CONTROL RESET'.
  • Diagnostic / Service ModePress CANCEL > CANCEL > START
  • Diagnostics / Auto Test1
  • Diagnostics Mode (Auto Test)1
  • Diagnostics Mode (Service Mode)Press CANCEL > CANCEL > START
  • DISPLAYFrom diagnostic mode, scroll to step 5 'DISPLAY'.
  • ENG MODEPress CANCEL > CANCEL > START to enter Service Mode
  • ENG MODE (Engineering Mode)From diagnostic mode, scroll to step 2 'ENG MODE'
  • FAULTSFrom diagnostic mode, scroll to step 7 'FAULTS'
  • RELAY USAGEFrom diagnostic mode, scroll to step 8 'RELAY USAGE'.
  • Temperature AdjustmentPress OPTIONS until 'Temp Calib' is displayed
  • Temperature Adjustment (Calibration)1. Press OPTIONS until 'Temp Calib' is displayed. The current offset is shown (or 0° if none). 2…
  • Temperature CalibrationPress OPTIONS until 'Temp Calib' is displayed
  • TEST MODEFrom diagnostic mode, scroll to step 3 'TEST MODE'.
  • TEST ON (Relay Checks)Press CANCEL > CANCEL > START
  • TEST ON (Relay Control)Available immediately upon entering diagnostic mode (CANCEL>CANCEL>START)
  • USAGEFrom diagnostic mode, scroll to step 1 'USAGE'.
  • VERSIONFrom diagnostic mode, scroll to step 4 'VERSION'.

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass