Model reference
Magic Chef 85RA-3BK
Cooktop
4 documents47 error codes13 service modes
Available documentation
Tech Sheet
- Instruction Sheet - Tech Sheet4 pg
- Tech Sheet - 975912010 pg
- tech sheet 9762882 reva8 pg
- TECH SHEET - WP Oven GMC275PDQ078 pg
MyPros+ Max
Diagnose your Magic Chef 85RA-3BK.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (47)
CodeMeaning
:Flashing colon indicates a power failure has occurred.E0Key held down too long or key is shorted (under F2).E0-F1EEPROM communications failure, possibly caused by power line noise or lightning.E0-F2Key contact closed for more than 60 secondsE0-F3Break in oven sensor circuitE0-F5Door switch open during CLEANE1Keypad keytail not connected (under F2).E1-F1EEPROM CHECKSUM failure, possibly caused by power line noise or lightning.E1-F2No communication between keyboard and controlE1-F3Short in oven sensor circuitE1-F5Latch switch not operatingE2-F3BAKE/BROIL temperature out of range (too high)E3-F1Fuel type (gas/electric) select failureE3-F3Clean temperature out of range (too high)E5CANCEL key drive line open (under F2).E6CANCEL key drive line open (under F2).E6-F2STOP/CLEAR key contact closed for more than 60 secondsF0-E0Electronic control malfunctionF01Temperature sensor opened (open circuit in oven temperature sensor).F02Welded element relays (element relay contacts fused closed).F05Door or latch problems (door latch assembly, latch motor, latch switch, or door…F06Electronic control malfunction.F1 E0EEPROM communications error.F1 E1EEPROM checksum failure.F1 E2UL A/D error(s).F1-E0Electronic control malfunctionF1-E1Electronic control malfunctionF1-E5Electronic control malfunctionF1-E6Electronic control malfunctionF2Default F codeView all 47 error codes
F2 E0Shorted key.F2 E1Keytail unplugged.F3 E0Oven sensor opened.F3 E1Oven sensor shorted.F3 E2BAKE/BROIL range over temperature.F3 E3CLEAN range over temperature.F3-E0Temperature sensor opened (R=2875 ohm by spec).F3-E1Temperature sensor shorted (R=825 ohm by spec).F3-E2Oven temp too highF3-E3Oven temp too highF3HHumidity sensor failure.F5 E0Door and switches do not agree.F5 E1Door latch not operating.F5 E2Latch error during CLEAN.F5-E0Door is open but latch is locked (door switch indicates open door while latch…F5-E1Self-clean latch will not lock/unlock.F6MW relay (Relay 4903) failure
Service modes (13)
- Bake Temperature Offset Adjustment1
- Cavity Size Programming1. Within 60 seconds of power up, press the following touchpads in order
- Fahrenheit to Celsius ConversionPress the BROIL pad for 5 seconds
- Fault Code DisplayPress and hold CANCEL key for 5 seconds
- Fault Code Display/VerificationPress and hold CANCEL key for 5 seconds
- Last Error Code RecallPress and hold CANCEL/OFF key for 5 seconds
- Manual Diagnostics Mode 1Within 120 seconds of power up, press STOP/CLEAR, STOP/CLEAR, then START.
- Manual Diagnostics Mode 2After 120 seconds of power up, press STOP/CLEAR, STOP/CLEAR, then START.
- Oven Temperature Adjustment (Calibration)Press and hold BAKE pad for 3 seconds. Current offset shown in 3-digit display, CAL shown in…
- Programming the Cavity Size1. Within 60 seconds of power up, press the following touchpads: OVEN CANCEL, WARM HOLD, BAKE, TEMP…
- Self-Diagnostic / Touch Panel and PCBA Test["Press and hold the OFF/CANCEL button while opening the door.","While still holding the OFF/CANCEL…
- Self-Diagnostic Test Mode (Touch Panel and PCBA Test)["Press and hold the OFF/CANCEL button while opening the door.","While still holding the OFF/CANCEL…
- Temperature Calibration AdjustmentPress and hold BAKE pad for 5 seconds
Full entry steps, exit procedures, and test sequences are available in Max.
Related Magic Chef cooktop models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax