mypros+
Model reference

Magic Chef 11HA-10K

Range

2 documents39 error codes18 service modes

Available documentation

Tech Tip

  • Instruction Sheet - 39795428 pg
    Covers this model
  • Instruction Sheet - 3977700 - Rev A8 pg
    Covers this model
MyPros+ Max

Diagnose your Magic Chef 11HA-10K.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (39)

CodeMeaning
1Thermistor short sensed10No wet clothes2Thermistor open sensed20Filling too quickly during cycle21Losing water during cycle (siphoning)22Losing water during cycle (siphoning)3Door circuit failure4Possible motor transistor error8Stuck keydCDoor circuit failuredoDoor openE1Thermistor is open (open circuit detected in the thermistor).E2Thermistor has shorted (short circuit detected in the thermistor).E3User interface (keyswitch) or software mismatch between the control…E6NTC open circuit failure (only alarmed during on-line test).E7NTC short circuit failure (only alarmed during on-line test).F1Water level circuit failure on control board (machine non functional).F12Motor sensor circuit failure on control board (machine functional)F13Blocked coin 2 or coin drop control circuit failure (machine non-functional).F2Membrane switch (touch panel) failure.F2E1Touch panel failure.F3HHumidity sensor out of range.F4Lid switch circuit failure on control board (machine non functional).F4E4Humidity sensor error.F5Blocked coin 1 or coin drop control circuit failure (machine non functional).F6Microwave relay failure.F7Slow fill detected; fill time greater than 5 minutes (machine functional).F8Slow drain detected; drain time greater than 2 minutes (machine functional).F8E5Exhaust air temperature detection failure.F9Low voltage detected; less than 90 volts AC (machine functional).
View all 39 error codes
FEPower source frequency errorhEHeating errorMemory FailureControl board memory/software failure detected during Field Service Test…Motor high currentMotor drawing excessive current detected during Field Service Test, indicated…Motor low currentMotor drawing insufficient current detected during Field Service Test…PFPower failure occurred while the dryer was running.Thermistor failureThermistor failure detected during Field Service Test, indicated by Heavy Wash…tSThermistor short sensedTurbidity Sensor failureTurbidity sensor failure detected during Field Service Test, indicated by Rinse…

Service modes (18)

  • Child Lock["Ensure the microwave oven and Timer are off.","Touch and hold CANCEL for 5 seconds until 2 tones…
  • Clear Diagnostic CodesWhile viewing the diagnostic code list in Service Mode, press the Sensor Dry Level and Time keypads…
  • Demo Mode["Microwave oven and Timer must be off.","Touch and hold Timer for 5 seconds until two tones sound…
  • Diagnostic / Test Mode["Plug in microwave oven or reconnect power.","Press CANCEL button to reach Standby mode (colon ':'…
  • Diagnostic Code Display1
  • Diagnostic Test Mode["Unit must be in Standby (unit plugged in, display off).","Alternately press the Less Time (∨) and…
  • Field Service TestPress the Heavy Wash key 5 times followed by the Start key within 6 seconds.
  • LED/Switch Check1. Enter Service Mode first. 2. Press Chime and Wrinkle Prevent keys simultaneously for 3 seconds…
  • Manual Function TestPress the Normal Wash key 5 times followed by the Start key within 6 seconds
  • On-Line Check Mode (Service Diagnostics Cycle)1
  • Operator/Programming ModeEnter operator mode using the service switch.
  • Sales Floor Demo ModePress Extra Rinse keypad 5 times within 6 seconds.
  • Service Mode1
  • Service Mode (Keypad/LED Test)Close the door, then within 60 seconds press RINSE ONLY and START/RESUME
  • System Check Mode1. Enter Service Mode first. 2. Press Time and Wrinkle Prevent keys simultaneously for 3 seconds…
  • Touch Panel and Electronic Control Diagnostic Test["Press and hold CANCEL while opening the door.","While still holding the CANCEL button, unplug the…
  • Touch Panel and Electronic Control Self-Diagnostic Test["Press and hold CANCEL while opening the door.","While still holding the CANCEL button, unplug the…
  • Washer Diagnostic Mode1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Magic Chef range models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax