mypros+
Model reference

Maytag DM15F-14B

Microwave

4 documents49 error codes16 service modes

Available documentation

Tech Sheet

  • Tech Sheet - 820660712 pg
    Covers this model
  • Tech Sheet - W11646013 - Rev A2 pg
    Covers this model

Tech Tip

  • Instruction Sheet - 82690922 pg
    Covers this model
  • Instruction Sheet - 82690932 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag DM15F-14B.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (49)

CodeMeaning
F0E1Load detected in drum during Clean Washer cycle.F0E2Excessive suds detected in washer; washer is running a suds reduction routine.F0E4High temperature error during wash cycle.F0E5Off balance load detected.F1.E1Relay control board defective.F12E0Communication between the Human Machine Interface and Wi-Fi Module has not been…F1E1Main relay open or shorted.F1E2MCU over- or under-voltage error.F1E4MW Relay Error 0F2.H1Hood keys stuck.F2.H2Hood/light switch defective.F2.Q1Not reading keypad inputs.F2E1Keypad stick errorF3.H1Humidity sensor failure.F3.T1UIB (user interface board) thermistor failure.F3.T4Magnetron thermistor failure.F3E1Pressure sensor signal missing or out of range.F3E2Wash NTC open or shorted.F3E5Dry NTC open circuit fault; dry temperature sensor out of range, open circuit…F3E6Accelerometer error.F3E8IR sensor failureF4E1Wash heater relay error or no feedback signal; ACU cannot detect temperature…F4E2Wash heater relay error.F4E3Hood NTC failureF4E4Blower error.F4E9MW relay synchronization Error 1F5E2Door lock failure.F5E3Door unlock failure.F5E4Door not open error.F6MW relay failure (relay 4903 contact may have welded closed).
View all 49 error codes
F6E1No communication from the HMI detected by ACU.F6E2No communication from the ACU detected by the HMI.F6E3No communication from the MCU detected by the ACU.F7Power to magnetron interrupted.F7E10Motor disconnected error.F7E12MC/MCU Overload.F7E2MC/MCU over temperature error or over current error/internal failure.F7E8MC/Motor over temperature error.F7E9Motor will not turn (Locked Rotor).F7EAMotor disconnected error (alternate display for F7E10).F7ECMC/MCU Overload (alternate display for F7E12).F8E1Long fill error.F8E3Overflow condition.F9Relay control board communications error.F9.QTouch communication error between UIB and touch panel.F9E1Long drain error.FCE0Communication between the Human Machine Interface and Wi-Fi Module has not been…FDE3Hood fan relay failureFDE4MWO Cooling fan error

Service modes (16)

  • Clear Error History["Enter Service Diagnostic Mode first.","From the DIAGNOSTICS HOME screen, press CLEAR ERROR…
  • Clear Fault Codes["Enter Service Diagnostic Mode.","From DIAGNOSTICS HOME screen, press CLEAR ERROR HISTORY button."]
  • Component Activation["Enter Service Diagnostic Mode first.","From DIAGNOSTICS HOME screen, press Component…
  • Component Activation (Manual)["Enter Service Diagnostic Mode (see above).","From DIAGNOSTICS HOME screen, press 'Component…
  • Control LockPress and hold Air Dry for 4 seconds
  • control_lockPress and hold Air Dry for 4 seconds
  • diagnosticWith the dishwasher in Standby (no cycle running), press the following keys in sequence
  • Diagnostic CycleWith the dishwasher in Standby (no cycle running), press the following option keys in sequence
  • diagnostic_cycleWith the dishwasher in Standby (no cycle running), press the following option keys in sequence
  • Fault/Error Code Display["Enter Service Diagnostic Mode first.","From the DIAGNOSTICS HOME screen, press ERROR DIAGNOSTIC…
  • Quick Service Cycle["Enter Service Diagnostic Mode first.","From Component Activation screen, select Quick Service…
  • Rapid Advance FeatureAfter starting a cycle, press the following option keys in sequence
  • rapid_advanceAfter starting a customer-selectable cycle, press the following option keys in sequence
  • Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Open and close the…
  • Software Version Display["Enter Service Diagnostic Mode first.","From DIAGNOSTICS HOME, press System Info, then Software…
  • Test Mode (Touch Panel and Relay Control Board Tests)["1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag microwave models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax