Model reference

Maytag JDR8895AA*

Name: Maytag JDR8895AA*
Brand: Maytag

Range

3 documents36 error codes27 service modes

Available documentation

Tech Sheet

Technical Information⎯Double Oven Dual Fuel Range11 pg
Covers this model

Service Manual

Maytag Heritage Wiring Diagrams _ Fault Codes MC 1124 pg
Covers this model

Other

IDC 0008 B1 pg
Covers this model

MyPros+ Max

Diagnose your Maytag JDR8895AA*.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Maytag Range

1c1c on my Maytag JDR8895AA*

M+

Shorted key detected on the control

From Tech Sheet W13534364, p.16:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (36)

CodeMeaning

1c1cShorted key detected on the control circuit board.1c2cKeyboard tail disconnected or keyboard loop reading improper value.1c31Cancel key circuit problem (cancel key improper value).1c32Cancel key circuit problem (cancel key improper value).1c4cPower micro communication failure (CRC invalid).1c6cEEPROM error (no response from EEPROM).1c7cControl not calibrated (calibration value out of range).1c81Cook profile corrupted in EEPROM (CRC invalid) for upper/single oven.1c82Cook profile corrupted in EEPROM (CRC invalid) for lower oven.1c8cCooking program error 1d11Runaway temperature (650°F) with door unlocked in upper/single oven cavity…1d12Runaway temperature (650°F) with door unlocked in lower oven cavity (sensor…1d21Runaway temperature (950°F) with door locked in upper/single oven cavity…1d22Runaway temperature (950°F) with door locked in lower oven cavity (sensor…3d11Temperature sensor failure (open) in upper/single oven cavity (sensor…3d12Temperature sensor failure (open) in lower oven cavity (sensor resistance is…3d21Temperature sensor failure (short) in upper/single oven cavity (sensor…3d22Temperature sensor failure (short) in lower oven cavity (sensor resistance < 0…3d41Meat probe shorted (probe resistance < 0 ohms).3d51Meat probe not calibrated (calibration value out of range).4d11Door switch position failure 4d12Door switch position failure 4d21No Reverse Airflow Fan rotation (no/low RPM) in upper/single oven.4d22No Reverse Airflow Fan rotation (no/low RPM) in lower oven.4d31Reverse Airflow Fan state error 4d32Reverse Airflow Fan state error 4d41High Reverse Airflow Fan rotation (high RPM) in upper/single oven.4d42High Reverse Airflow Fan rotation (high RPM) in lower oven.4d51Door switch circuit failure 4d52Door switch circuit failure

View all 36 error codes

9d11Latch will not lock in upper/single oven (lock switch not closed).9d12Latch will not lock in lower oven (lock switch not closed).9d21Latch will not unlock in upper/single oven (unlock switch not closed).9d22Latch will not unlock in lower oven (unlock switch not closed).9d31Latch both locked and unlocked simultaneously in upper/single oven (lock and…9d32Latch both locked and unlocked simultaneously in lower oven (lock and unlock…

Service modes (27)

24 Hour Clock TogglePress and hold Upper Cancel and Favorite pads for 3 seconds.
Beeper Volume AdjustmentPress and hold Upper Cancel and Delay pads for 3 seconds.
Child Lock OutPress and hold Upper Cancel and Cook & Hold pads for 3 seconds
Clock Display Toggle (On/Off)Press and hold Upper Cancel and Clock pads for 3 seconds.
Diagnostic Code Display ModePress and hold Upper Cancel and Autoset pads for 3 seconds
Diagnostic Code Display Mode (H1)Press and hold the Autoset pad for 3 seconds at power-up.
Diagnostic Code Display Mode (H2.5)Press and hold Upper Cancel and Autoset pads for 3 seconds
Diagnostic Code Display Mode (H3)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up
Diagnostic Code Display Mode (M1/M2)Diagnostic Code Display Mode can only be started within 30 seconds when powering up the control.
Diagnostic Code Display Mode (NSC)Press and hold More + pad for 3 to 5 seconds within 60 seconds of powering up the unit. Cycle…
Factory Default ResetPress and hold Upper Cancel and Upper Keep Warm pads for 3 seconds.
Faults Access (EOC III)1
One-Watt Standby Mode (NSC)Press and hold Cancel and Less
Oven Temperature Adjustment - Lower OvenPress Lower Bake pad
Oven Temperature Adjustment - Upper OvenPress Upper Bake pad
Quick Test ModePress and hold CANCEL and BROIL pads simultaneously for 3 seconds
Quick Test Mode (EOC III)1
Quick Test Mode (H1 Convection Model)1. Press and hold Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
Quick Test Mode (H1 Non-Convection Model)1. Press and hold Cancel and Toast pads for 3 seconds. 2. Release both pads. 3. Press pads
Quick Test Mode (H2/H2.5 Control)1. Press and hold Cancel and Broil pads for 3 to 5 seconds. 2. Release both pads. 3. Press pads
Quick Test Mode (H3 Control)1. Press and hold Upper Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
Quick Test Mode (M1/M2 Control)1. Press and hold Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
Quick Test Mode (NSC Non-Self Cleaning Control)1. Press and hold Cancel and Broil pads for 3 to 5 seconds within 5 minutes of power-up. 2. Release…
Sabbath ModeHold Clock pad for 3 to 5 seconds to activate Sabbath mode.
Service Mode (EOC III)1
Temperature Display Toggle (°F/°C)Press and hold Upper Cancel and Upper Bake pads for 3 seconds.
Test Mode (UH Control)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass