mypros+
Model reference

Maytag LER3330AAW

Range

7 documents36 error codes27 service modes

Available documentation

Tech Sheet

  • Tech Sheet - 160261058 pg
    Covers this model

Service Manual

  • Service Manual - Freestanding Electric Range54 pg
    Covers this model
  • Freestanding Electric Range Service Manual54 pg
    Covers this model
  • Failure Codes and Wiring Diagrams for Maytag Heritage Gas & Electric Ranges124 pg
    Covers this model
  • FAILURE CODES AND WIRING DIAGRAMS for MAYTAG HERITAGE GAS & ELECTRIC RANGES124 pg
    Covers this model

Bulletin

  • Technical Bulletin - Wiring replacement dual infinite switch1 pg
    Covers this model
  • Technical Bulletin - TDC-0090-B Wiring replacement dual infinite switch1 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag LER3330AAW.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (36)

CodeMeaning
1c1cShorted key detected; control disables audible feedback for affected key…1c2cKeyboard tail disconnected; keyboard loop returns improper value.1c31Cancel key circuit problem; cancel key returns improper value.1c32Cancel key circuit problem (cancel key improper value) on lower oven cavity.1c4cPower micro communication failure (CRC invalid).1c6cEEPROM error; no response from EEPROM after 3 tries.1c7cControl not calibrated; calibration value out of range.1c81Cook profile corrupted in EEPROM for upper/single oven cavity (CRC invalid).1c82Cook profile corrupted in EEPROM for lower oven cavity (CRC invalid).1c8cCooking program error; CRC invalid when cook or clean is programmed.1d11Runaway temperature (650°F) detected with door unlocked; sensor resistance…1d12Runaway temperature (650°F) detected with door unlocked on lower oven cavity.1d21Runaway temperature (950°F) detected with door locked; sensor resistance…1d22Runaway temperature (950°F) detected with door locked on lower oven cavity.3d11Oven temperature sensor open; sensor resistance reads infinite ohms.3d12Temperature sensor failure (open) on lower oven cavity3d21Oven temperature sensor shorted; sensor resistance reads 0 ohms.3d22Temperature sensor failure (short) on lower oven cavity3d41Meat probe shorted3d51Meat probe not calibrated4d11Door switch not closed when door is locked.4d12Door switch position failure4d21No Reverse Airflow Fan rotation (no/low RPM) on upper/single oven cavity.4d22No Reverse Airflow Fan rotation (no/low RPM) on lower oven cavity.4d31Reverse Airflow Fan state error4d32Reverse Airflow Fan state error4d41High Reverse Airflow Fan rotation (high RPM) on upper/single oven cavity.4d42High Reverse Airflow Fan rotation (high RPM) on lower oven cavity.4d51Door switch not open or closed (invalid state detected).4d52Door switch circuit failure
View all 36 error codes
9d11Latch will not lock; lock switch not closed when it should be locked.9d12Door latch will not lock on lower oven cavity9d21Door latch will not unlock on upper/single oven cavity9d22Door latch will not unlock on lower oven cavity9d31Door latch both locked and unlocked simultaneously on upper/single oven9d32Door latch both locked and unlocked simultaneously on lower oven

Service modes (27)

  • 24 Hour Clock Toggle["Press and hold Cancel and Delay pads for 3 to 5 seconds.","Press More + or Less
  • Child Lock Out["Press and hold Cancel and Cook & Hold pads for 3 to 5 seconds until beep sounds."]
  • Clock Display Toggle["Press and hold Cancel and Clock pads for 3 to 5 seconds."]
  • Clock Display Toggle (On/Off)["Press and hold Cancel and Clock pads for 3 to 5 seconds."]
  • Diagnostic Code Display["Power up the unit.","Within 60 seconds of powering up, press and hold the More + pad.","Cycle…
  • Diagnostic Code Display Mode["Must be started within 60 seconds of powering up the control.","Press and hold More + pad within…
  • Diagnostic Code Display Mode (H1 Controls)Press and hold AUTOSET pad for 3 seconds at power-up.
  • Diagnostic Code Display Mode (H3 Controls)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up.
  • Diagnostic Code Display Mode (NSC Controls)Press and hold the More + pad for 3 to 5 seconds when powering up the unit (within 60 seconds of…
  • Factory Default Reset["Press and hold Cancel and Keep Warm pads for 3 to 5 seconds until beep sounds."]
  • Faults Access (EOC III Controls)1
  • One-Watt Standby Mode (NSC Controls)Press and hold Cancel and Less
  • Oven Temperature Adjustment["Press Bake pad.","Enter 550 on the digit-pad.","Immediately press and hold Bake pad for 3 to 5…
  • Quick Test["Must be entered within the first 5 minutes after power up.","Press and hold Cancel and Broil pads…
  • Quick Test Mode["Must be entered within the first 5 minutes after power up.","Press and hold Cancel and Broil pads…
  • Quick Test Mode (EOC III Controls)1
  • Quick Test Mode (H1 Controls - Convection Model)1
  • Quick Test Mode (H1 Controls - Non-Convection Model)1
  • Quick Test Mode (H2/H2.5 Controls)1
  • Quick Test Mode (H3 Controls)1
  • Quick Test Mode (M1/M2 Controls)1
  • Quick Test Mode (NSC Non-Self Clean Controls)1
  • Sabbath Mode["Initiate desired bake function before entering Sabbath mode.","Hold Clock button for 3 to 5…
  • Service Mode (EOC III Controls)1
  • Temperature Display (°F/°C toggle)["Press and hold Cancel and Bake pads for 3 to 5 seconds.","Press More + or Less
  • Temperature Display Toggle (°F/°C)["Press and hold Cancel and Bake pads for 3 to 5 seconds.","Press More + or Less
  • Test Mode (UH Controls)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass