Model reference
Maytag MES5875BCW20
Range
9 documents27 error codes25 service modes
Available documentation
Tech Sheet
- Electric Slide-In Range⎯Technical Information16 pg
- Electric Slide-In Range⎯Technical Information10 pg
Service Manual
- Service Manual - 16026299_1602629945 pg
Bulletin
- Technical Bulletin - Hot Surface Indicator Light Change1 pg
- Installation Bulletin1 pg
- Technical Bulletin - TDC-0096-B-French Oven Door Handles Breaking2 pg
Service Flash
- Technical Bulletin - TDC-0096-B Oven Door Handles Breaking_TDC-0096-B2 pg
Installation Guide
- Installation Bulletin2 pg
Other
- TDC 0096 B2 pg
MyPros+ Max
Diagnose your Maytag MES5875BCW20.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (27)
CodeMeaning
1c1cShorted key detected on control circuit board.1c2cKeyboard tail disconnected; keyboard loop reading improper value.1c31Cancel key circuit problem (cancel key improper value).1c32Cancel key circuit problem (cancel key improper value).1c6cEEPROM error; no response from EEPROM after 3 tries.1c7cControl not calibrated; calibration value out of range.1c8cCooking program error; CRC invalid.1d11Runaway temperature (650°F) detected with door unlocked; sensor resistance >…1d12Runaway temperature (650°F) detected with door unlocked; sensor resistance >…1d21Runaway temperature (950°F) detected with door locked; sensor resistance > 2787…1d22Runaway temperature (950°F) detected with door locked; sensor resistance > 2787…3d11Temperature sensor open; sensor resistance reads infinite ohms.3d12Temperature sensor open; sensor resistance reads infinite ohms.3d21Temperature sensor shorted; sensor resistance reads 0 ohms.3d22Temperature sensor shorted; sensor resistance reads 0 ohms.4d11Door switch position failure; door switch not closed when door is locked.4d12Door switch position failure; door switch not closed when door is locked.4d21No reverse airflow fan rotation (no or low RPM detected).4d31Reverse airflow fan is on when it should be off.4d51Door switch circuit failure; door switch not reading open or closed.4d52Door switch circuit failure; door switch not reading open or closed.9d11Latch will not lock; lock switch not closed when it should be locked.9d12Latch will not lock; lock switch not closed when it should be locked.9d21Latch will not unlock; unlock switch not closed when it should be unlocked.9d22Latch will not unlock; unlock switch not closed when it should be unlocked.9d31Latch state unknown; both locked and unlocked switches reading simultaneously.9d32Latch state unknown; both locked and unlocked switches reading simultaneously.Service modes (25)
- 24 Hour Clock TogglePress and hold Cancel and Favorite pads for 3 to 5 seconds.
- Child Lock OutPress and hold Cancel and Cook & Hold pads for 3 to 5 seconds
- Child Lockout["Press and hold Cancel and Cook & Hold pads for 3 to 5 seconds.","'OFF' will display where the…
- Clock Display TogglePress and hold Cancel and Clock pads for 3 to 5 seconds.
- Diagnostic Code Display ModePress and hold the AUTOSET pad for 3 to 5 seconds at power-up
- Diagnostic Code Display Mode (H1 / MES5775BC*, MES5875BC*)["At power-up, press and hold the AUTOSET pad for 3 to 5 seconds.","Cycle through the stored codes…
- Diagnostic Code Display Mode (M2 / AES3760BC*)["At power-up, press and hold the AUTOSET pad for 3 to 5 seconds.","Cycle through the stored codes…
- Factory Default ResetPress and hold Cancel and Keep Warm pads for 3 to 5 seconds.
- H1 Diagnostic Code Display["Press and hold the AUTOSET pad for 3 to 5 seconds at power-up.","Can only be started while…
- H1 Quick Test Mode["Press and hold Cancel and Broil pads for 3 to 5 seconds.","Once the control enters Quick Test…
- M1 Child Lockout["Press and hold Cancel and Cook & Hold pads for 3 to 5 seconds until beep sounds."]
- M1 Diagnostic Code Display["Must be started within 60 seconds of powering up the control.","Press and hold the slew up…
- M1 Factory Default Reset["Press and hold Cancel and Keep Warm pads for 3 to 5 seconds until beep sounds."]
- M1 Oven Temperature Adjustment["Press Bake pad.","Enter 550 on the digit-pad.","Immediately press and hold Bake pad for 3 to 5…
- M1 Quick Test Mode["Must be entered within the first 5 minutes after power up.","Temperature sensor must be below…
- M1 Sabbath Mode["Initiate desired bake function first.","Hold Clock button for 3 to 5 seconds to activate Sabbath…
- M2 Diagnostic Code Display["Press and hold the AUTOSET pad for 3 to 5 seconds at power-up.","Can only be started while…
- M2 Quick Test Mode["Must be entered within the first 5 minutes after power up.","Temperature sensor must be below…
- Oven Temperature AdjustmentPress BAKE pad, enter 550 on the digit-pad, then immediately press and hold BAKE pad for 3 to 5…
- Oven Temperature Adjustment Mode["Press BAKE pad.","Enter 550 on the digit-pad.","Immediately press and hold BAKE pad for 3 to 5…
- Quick Test ModePress and hold CANCEL and BROIL pads simultaneously for 3 to 5 seconds
- Quick Test Mode (H1 / MES5775BC*, MES5875BC*)["Press and hold CANCEL and BROIL pads simultaneously for 3 to 5 seconds.","Once the control has…
- Quick Test Mode (M2 / AES3760BC*)["Power up the unit (must enter within first 5 minutes after power up).","Press and hold CANCEL and…
- Sabbath ModeHold CLOCK button for 3 to 5 seconds to activate Sabbath mode
- Temperature Display Toggle (°F/°C)Press and hold Cancel and Bake pads for 3 to 5 seconds.
Full entry steps, exit procedures, and test sequences are available in Max.
Related Maytag range models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass