mypros+
Model reference

Maytag MET8775XB00

Range

5 documents48 error codes14 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10311746 - Rev A16 pg
    Covers this model
  • Tech Sheet - W1045710416 pg
    Covers this model

Service Manual

  • Troubleshooting Gas and Electric Freestanding Range Electronic Controls70 pg
    Covers this model

Installation Guide

  • Installation Instructions20 pg
    Covers this model
  • Instruction Sheet1 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MET8775XB00.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (48)

CodeMeaning
E0 F1EEPROM communication error.E0 F2Keypad disconnected.E0 F3Main temperature sensor open or shorted (upper oven).E0 F5Door and latch switches do not agree (Clean mode).E0 F6Lost communications.E0 F9Product is mis-wired.E1 F1Upper RTD uncalibrated.E1 F2Stuck key.E1 F3Main temperature sensor open or shorted (lower oven).E1 F5Door latch not operating (Clean mode).E1 F6Over temperature during cook mode (runaway temperature).E2 F1Lower RTD uncalibrated.E2 F2Stuck key.E2 F6Over temperature during clean mode (runaway temperature).E3 F6Over temperature in warming drawer (runaway temperature).E5 F1Sensor usage out of range.E7 F1PCB Thermistor/Sensor open or shorted.E9 F1WIDE Queue full.F1Control failure or UL A/D error(s) detected in the control board.F1 E*Control board failure (all F1 sub-codes indicate control fault).F1-E0EEPROM communication error.F1-E1Upper RTD uncalibrated.F1-E2Lower RTD uncalibrated.F1-E5Sensor usage out of range.F1-E7PCB thermistor/sensor open or shorted.F1-E9WIDE Queue full.F2Shorted/stuck key detected on the control keypad.F2-E0Keypad disconnected.F2-E1Stuck key.F2-E2Stuck key.
View all 48 error codes
F3Oven sensor opened or oven sensor shorted.F3 E0Oven temperature sensor fault (open or shorted)F3 E1Lower oven temperature sensor fault (MRC II double oven models).F3 E2Warming drawer temperature sensor fault.F3-E0Upper oven main sensor open or shorted.F3-E1Lower oven main sensor open or shorted.F5 E0Door position switch faultF5 E1Door latch switch/system faultF5 E2Door switch fault.F5-E0Door and latch switches do not agree during Clean mode.F5-E1Door latch not operating during Clean mode.F6 E*Control communication failure.F6-E0Lost communications.F6-E1Over temperature during cook mode (runaway temp).F6-E2Over temperature during clean mode (runaway temp).F6-E3Over temperature in warming drawer (runaway temp).F9House miswiredF9-E0Product is mis-wired.

Service modes (14)

  • Diagnostics ModePress CANCEL > CANCEL > START
  • Diagnostics Mode / Semi Automatic Test ModePress CANCEL > CANCEL > START within 5 seconds
  • Faults (Error Code Review)1
  • Faults DisplayEnter Diagnostics Mode, then press TEMP/TIME '+' or '-' keypads (or Number 3 or 6 keypads depending…
  • LCC Diagnostic Mode (LCC90/LCC95/LCC180)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • LCC190 Diagnostic Mode (Self Clean, Convection models)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME or TEMP/HOUR '+' key to cycle through…
  • MRC Diagnostic Mode["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC Diagnostic Mode (Fan/True Convection Electric - Oven Light entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC II Diagnostic Mode (Number 3 key entry - KitchenAid models)["Press OFF/OFF/START or CANCEL/CANCEL/START in sequence.","Press the number '3' key to cycle…
  • MRC II Diagnostic Mode (TEMP/TIME entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' keypad to cycle through diagnostic…
  • Semi Automatic TestEnter Diagnostics Mode, then press TEMP/TIME '+' or '-' keypads (or Number 3 or 6 keypads depending…
  • Temperature CalibrationPress SETTINGS/OPTIONS until 'Temp Calib' is highlighted, then follow instructions to see…
  • Test Mode1
  • Test Mode (manual relay activation)Enter Diagnostics Mode, then press TEMP/TIME '+' or '-' keypads (or Number 3 or 6 keypads depending…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass