mypros+
Model reference

Maytag PGS3759BDB

Range

6 documents30 error codes15 service modes

Available documentation

Tech Sheet

  • Gas Slide-In Range⎯Technical Information8 pg
    Covers this model

Service Manual

  • Service Manual - 1602629355 pg
    Covers this model

Bulletin

  • Technical Bulletin - TDC-0086-B-French Clock fails or fades out when using bake or broil function1 pg
    Covers this model

Tech Tip

  • Instruction Sheet2 pg
    Covers this model

Installation Guide

  • Instruction Sheet2 pg
    Covers this model

Other

  • TDC 0099 B1 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag PGS3759BDB.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (30)

CodeMeaning
1c1cShorted key detected; disables audible for key depression and disables key.1c2cKeyboard tail disconnected1c31Cancel key circuit problem; cancel key has improper value.1c32Cancel key circuit problem (H1 control, second cavity designation).1c4cMicro communication failure; checksum invalid after 5 serial communication…1c5cVcc or ground fault; Vcc/Gnd at test point out of range, disables all outputs.1c6cEEPROM error; no response from EEPROM after 5 tries.1c7cControl not calibrated; calibration value out of range.1c8cCooking program error; CRC invalid, disables all outputs.1d11Runaway temperature (650°F) detected with door unlocked; sensor resistance…1d12Runaway temperature (650°F) with door unlocked (H1 control, second cavity).1d21Runaway temperature (950°F) detected with door locked; sensor resistance…1d22Runaway temperature (950°F) with door locked (H1 control, second cavity).3d11Temperature sensor open; sensor resistance is infinite3d12Sensor open (H1 control, second cavity)3d21Temperature sensor shorted; sensor resistance is 0 Ohms3d22Sensor shorted (H1 control, second cavity)4d11Door position switch not closed when door is locked; disables Clean function.4d12Door switch position failure (H1 control, second cavity).4d21No reverse airflow fan rotation (no/low RPM) detected during clean or cook.4d31Reverse airflow fan state error4d51Door switch circuit failure4d52Door switch circuit failure (H1 control, second cavity).9d11Latch will not lock; lock switch not closed when Clean activated9d12Latch will not lock (H1 control, second cavity).9d21Latch will not unlock; lock switch closed when Clean not activated9d22Latch will not unlock (H1 control, second cavity).9d31Unlock state unknown9d32Latch state unknown, both locked and unlocked (H1 control, second cavity).9d41Unlock state unknown

Service modes (15)

  • 24-Hour Clock TogglePress and hold CANCEL and DELAY pads for 3 to 5 seconds
  • Child LockoutPress and hold CANCEL and COOK & HOLD pads for 3 to 5 seconds until beep sounds.
  • Clock Display TogglePress and hold CANCEL and CLOCK pads for 3 to 5 seconds.
  • Diagnostic Code DisplayPress and hold MORE+ pad within 5 minutes of powering up the unit
  • Factory Default ResetPress and hold CANCEL and KEEP WARM pads for 3 to 5 seconds.
  • H1 Diagnostic Code Display1
  • H1 Quick Test Mode1. At power-up or within 5 minutes of power-up, press and hold Cancel and Broil pads for 5 seconds…
  • M1 Diagnostic Code Display1
  • M1 Quick Test Mode1. Power up the unit. 2. Within 5 minutes of power up, press and hold CANCEL and BROIL pads for 5…
  • M2 Diagnostic Code Display1
  • M2 Quick Test Mode1. Power up the unit. 2. Within 5 minutes of power up, press and hold CANCEL and BROIL pads for 5…
  • Oven Temperature Adjustment1
  • Quick Test1
  • Sabbath ModeHold CLOCK pad for 3 to 5 seconds to activate Sabbath mode
  • Temperature Display Toggle (°F/°C)Press and hold CANCEL and BAKE pads for 3 to 5 seconds

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass