mypros+
Model reference

Maytag YMER8800FW3

Range

8 documents27 error codes22 service modes

Available documentation

Tech Sheet

  • Tech Sheet28 pg
    Covers this model
  • Tech Manual16 pg
    Covers this model
  • Fiche technique - Tech Sheet W10667176 Rev A8 pg
    Covers this model
  • Tech Sheet - W10667169 - Rev C8 pg
    Covers this model

Service Manual

  • Tech Manual16 pg
    Covers this model
  • Tech Manual - W11401670 - Rev A16 pg
    Covers this model

Quick Reference

  • Freestanding Electric Range Control Guide19 pg
    Covers this model
  • Quick Start Guide2 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag YMER8800FW3.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (27)

CodeMeaning
F1-E0EEPROM communication error.F1-E5Sensor out of range.F1-E7Circuit board thermistor open or short-circuited.F1E0EEPROM communication error.F1E5Sensor out of range.F1E7PCB thermistor open or shorted.F1E9WIDE File queue full.F2-E0Keypad disconnected.F2-E1Stuck key.F2-E2Cancel key error.F2E0Keypad disconnected.F2E1Stuck key.F2E2Cancel key error.F3-E0Oven temperature sensor open or short-circuited (measured at P10-1 and P10-2).F3-E2Oven temperature sensor issue (measured at P10-3 and P10-4, warm drawer sensor).F3E0Main oven sensor open or shorted.F3E2Warming drawer sensor open or shorted.F5-E0Door switch/latch fault (measured at P7-5 and P7-4).F5E0Door and switch do not agree (Clean modeF5E1Door latch not functional (Clean modeF6-E1Excessive temperature fault.F6-E2Excessive temperature fault.F6-E3Excessive temperature fault.F6E1Over temperature during cook mode.F6E2Over temperature during clean mode.F6E3Over temperature in warming drawer.F9E0Mis-wired house or range.

Service modes (22)

  • Auto TestFrom service mode (CANCEL > CANCEL > START), press up arrow / '+' / '3' to scroll to 'AUTO TEST'…
  • CONTROL RESETFrom Service Mode, scroll to step 6 (CONTROL RESET).
  • Diagnostics Mode (Auto Test)1
  • Diagnostics Mode (MRC Control)Press CANCEL > CANCEL > START
  • Diagnostics Mode (Service Mode Entry)Press CANCEL > CANCEL > START
  • Diagnostics Mode (Service Mode)Press CANCEL > CANCEL > START
  • DISPLAYFrom Service Mode, scroll to step 5 (DISPLAY).
  • ENG MODEFrom Service Mode, scroll to step 2 (ENG MODE)
  • ENG MODE (Engineering Mode)From service mode, scroll to step 2 'ENG MODE'
  • FAULTSFrom Service Mode, scroll to step 7 (FAULTS).
  • MRC Control Module Diagnostics / Service ModePress CANCEL > CANCEL > START to enter service mode
  • RELAY USAGEFrom Service Mode, scroll to step 8 (RELAY USAGE).
  • Service Diagnostic Mode / Auto Test["Press CANCEL > CANCEL > START to enter the diagnostic mode.","Press the up arrow, '+' (plus…
  • Temperature AdjustmentStep 1
  • Temperature CalibrationPress OPTIONS until 'Temp Calib' is displayed
  • Temperature Offset AdjustmentPress OVEN LIGHT for 5 seconds
  • TEST MODEFrom Service Mode, scroll to step 3 (TEST MODE)
  • TEST ONUpon entering service mode (CANCEL>CANCEL>START), TEST ON is the first screen displayed.
  • TEST ON - Relay ControlEnter service mode (CANCEL > CANCEL > START)
  • TEST ON (Relay Checks)Available upon entry to Service Mode (CANCEL > CANCEL > START)
  • USAGEFrom Service Mode, scroll to step 1 (USAGE).
  • VERSIONFrom Service Mode, scroll to step 4 (VERSION).

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass