Model reference

Whirlpool WED9200SQ2

Dryer

11 documents24 error codes11 service modes

Available documentation

Tech Sheet

Whirlpool Duet Dryer WED9200SQ0 Tech Sheet12 pg
Covers this model
TECH SHEET12 pg
Covers this model
TECH SHEET - Whirlpool Dryer WED9500TW312 pg
Covers this model
Tech Sheet W1011063812 pg
Covers this model

Bulletin

Whirlpool 27 Inch Dryers - Door not Closing Properly or Popping Open4 pg
Covers this model

Service Flash

Service Pointer - 8178673 - Door Not Closing Properly or Popping Open4 pg
Covers this model

Tech Tip

Instruction Sheet - W10128087- Rev A - Special Handling7 pg
Covers this model
Instruction Sheet2 pg
Covers this model
Instruction Sheet12 pg
Covers this model

Installation Guide

Instrucciones de instalacion20 pg
Covers this model
Installation Instructions16 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool WED9200SQ2.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (24)

CodeMeaning

F:01Primary control failure.F:02Stuck button or user interface mismatch (only appears in diagnostic test mode).F:20No voltage detected at the heater relay (appears ONLY in Diagnostic Test Mode).F:22Outlet thermistor is open.F:23Outlet thermistor has shorted.F:24Inlet thermistor is open (only appears in diagnostic test mode).F:25Inlet thermistor has shorted (only appears in diagnostic test mode).F:26Motor drive system failure.F:28Moisture sensor strip is open (only appears in diagnostic test mode).F:29Moisture sensor strip has shorted (only appears in diagnostic test mode).F:30Restricted airflow condition exists (only appears in diagnostic test mode).F:31Low voltage condition (less than 30V) detected (appears ONLY in Diagnostic Test…F:50No voltage detected at the water valve relay (appears ONLY in Diagnostic Test…F:70No communication between the machine control and the console electronics.F:71No communication between the machine control and the console electronics.F:72Console electronics failure.F:73Console electronics failure.F:74Console electronics failure.F:75Console electronics failure.F:76Console electronics failure.F:77Console electronics failure.F:78Console electronics failure.L2Low line voltage (less than 30V) detected at installation.PFA power failure occurred while the dryer was running.

Service modes (11)

Adjusting Customer-Focused Drying Modes (TEST #5a)1
Customer-Focused Drying Mode Adjustment1
Customer-Focused Drying Mode Adjustment (CF1/CF2/CF3)["Activate the diagnostic test mode and advance past saved fault codes.","Press and hold the…
Diagnostic Test Mode1
Displaying Inlet Air FlowAfter all saved fault codes have been displayed in diagnostic mode, press the Wrinkle Shield button…
Displaying Line VoltageAfter all saved fault codes have been displayed in diagnostic mode, press the Cycle Signal button
Inlet Air Flow Diagnostic["Enter the Service Diagnostic Test Mode.","After all saved fault codes have been displayed, press…
Line Voltage Diagnostic["Enter the Service Diagnostic Test Mode.","After all saved fault codes have been displayed, press…
Line Voltage DisplayAfter entering the Diagnostic Test Mode, waiting for the 5 second delay, and cycling through any…
Manual Load Test["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…
Service Diagnostic Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool dryer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass