Model reference
Whirlpool WGD9400SW0
Dryer
12 documents24 error codes8 service modes
Available documentation
Tech Sheet
- Tech Sheet W1011064016 pg
- Whirlpool Dryer YWED9200SQ0 Tech Sheet16 pg
- Diagnostic Guide and Service Manual16 pg
Service Flash
- Service Pointer - 8178673 - Door Not Closing Properly or Popping Open4 pg
- Dry Time Display Appears to Jump or Stall4 pg
- Service Pointer - 8178790 (Door not Closing)6 pg
Tech Tip
- Instruction Sheet - 8574875 - Rev A - Special Handling4 pg
- Instruction Sheet2 pg
- Instruction Sheet12 pg
Other
- 81786734 pg
- Service Pointer 81787334 pg
Quick Reference
- Quick Reference Manual2 pg
MyPros+ Max
Diagnose your Whirlpool WGD9400SW0.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (24)
CodeMeaning
AFLow inlet air flow detected at install.F:01Primary control failure.F:02Stuck button or user interface mismatch; this fault code will ONLY appear when…F:20No voltage detected at the heater relay; appears ONLY in Diagnostic Test Mode.F:22Outlet thermistor is open.F:23Outlet thermistor has shorted.F:24Inlet thermistor is open; this fault code will ONLY appear when in the…F:25Inlet thermistor has shorted; this fault code will ONLY appear when in the…F:26Motor drive system failure.F:28Moisture sensor strip is open; this fault code will ONLY appear when in the…F:29Moisture sensor strip has shorted; this fault code will ONLY appear when in the…F:30Restricted airflow condition exists; this fault code will ONLY appear when in…F:31Low voltage condition (less than 30V) detected; appears ONLY in Diagnostic Test…F:70No communication between the machine control and the console electronics.F:71No communication between the machine control and the console electronics.F:72Console electronics failure (F:72 through F:78).F:73Console electronics failure (F:72 through F:78).F:74Console electronics failure (F:72 through F:78).F:75Console electronics failure (F:72 through F:78).F:76Console electronics failure (F:72 through F:78).F:77Console electronics failure (F:72 through F:78).F:78Console electronics failure (F:72 through F:78).L2Low line voltage (less than 30V) detected at installation.PFPower failure occurred while the dryer was running.Service modes (8)
- Adjusting Customer-Focused Drying Modes (CF1/CF2/CF3)1
- Customer-Focused Drying Mode Adjustment (CF1/CF2/CF3)["In Standby mode (dryer plugged in but not powered up), press and hold the Dryness Level button…
- Diagnostic Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…
- Displaying Inlet Air Flow["Activate diagnostic test mode and advance past all saved fault codes.","Press the Wrinkle Shield…
- Displaying Line Voltage["Activate diagnostic test mode and advance past all saved fault codes.","Press the Cycle Signal…
- Manual Load Test1. Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…
- Manual Load Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…
- Service Diagnostic Test Mode1. Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool dryer models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass