Model reference

Whirlpool WGD9470WW2

Dryer

7 documents25 error codes7 service modes

Available documentation

Tech Sheet

Tech Sheet - W1029885056 pg
Covers this model
Whirlpool Dryer YWED9500TW3 Tech Sheet56 pg
Covers this model

Service Flash

Rubber Seal in W10206708 Hose Kit for 'Y' Connector2 pg
Covers this model

Tech Tip

Instruction Sheet - W10128087- Rev A - Special Handling7 pg
Covers this model
Instruction Sheet2 pg
Covers this model
Instruction Sheet12 pg
Covers this model

Installation Guide

Instrucciones de instalacion16 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool WGD9470WW2.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Dryer

af on my Whirlpool WGD9470WW2

M+

Low inlet air flow condition detected

From Tech Sheet W15028188, p.40:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (25)

CodeMeaning

afLow inlet air flow condition detected at installation (Amana models only).f:01Primary control failure.f:02Stuck button or user interface mismatch (appears ONLY in Diagnostic Test Mode).f:20Heater failure f:22Outlet thermistor is open.f:23Outlet thermistor has shorted.f:24Inlet thermistor is open (Amana models only, appears ONLY in Diagnostic Test…f:25Inlet thermistor is shorted (Amana models only, appears ONLY in Diagnostic Test…f:26Motor drive system failure.f:28Moisture sensor strip is open (appears ONLY in Diagnostic Test Mode).f:29Moisture sensor strip has shorted (appears ONLY in Diagnostic Test Mode).f:30Restricted air flow condition exists (Amana models only, appears ONLY in…f:31L2 line voltage error f:50Water valve failure f:70No communication between the machine control and the console electronics.f:71No communication between the machine control and the console electronics.f:72Console electronics failure (F:72 through F:78).f:73Console electronics failure (F:72 through F:78).f:74Console electronics failure (F:72 through F:78).f:75Console electronics failure (F:72 through F:78).f:76Console electronics failure (F:72 through F:78).f:77Console electronics failure (F:72 through F:78).f:78Console electronics failure (F:72 through F:78).l2Low line voltage (less than 30V) detected at installation.pfPower failure occurred while the dryer was running.

Service modes (7)

Customer-Focused Drying Mode Adjustment (CF1/CF2/CF3)1
Diagnostic Test Mode1. Dryer must be in standby mode (plugged in with all indicators off, or with only Done/Dry/Clothes…
Displaying Inlet Air Flow Diagnostic (Amana Electric Models Only)["Enter the Diagnostic Test Mode.","Wait for the 5 second delay and cycle through any saved fault…
Displaying Line Voltage Diagnostic["Enter the Diagnostic Test Mode.","Wait for the 5 second delay and cycle through any saved fault…
Inlet Air Flow Diagnostic (Amana Electric Models Only)After entering the Diagnostic Test Mode and cycling through saved fault codes, press the Wrinkle…
Line Voltage DiagnosticAfter entering the Diagnostic Test Mode and cycling through saved fault codes, press the Cycle…
Manual Load Test1. Dryer must be in standby mode. 2. Select any one button except Pause/Cancel and Controls…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool dryer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass