Model reference

Whirlpool WGD9500TC1

Dryer

10 documents25 error codes7 service modes

Available documentation

Tech Sheet

Tech Sheet - W10177456A12 pg
Covers this model
TECH SHEET - W10050531A WGD9500TC0 duet steam dryer12 pg
Covers this model
TECH SHEET - WGD9500TC2 duet steam dryer12 pg
Covers this model

Service Flash

Dry Time Display Appears to Jump or Stall4 pg
Covers this model
Service Pointer - 8178790 (Door not Closing)6 pg
Covers this model

Tech Tip

Instruction Sheet - W10128087- Rev A - Special Handling7 pg
Covers this model
Instruction Sheet2 pg
Covers this model
Instruction Sheet12 pg
Covers this model

Installation Guide

Installation Instructions32 pg
Covers this model
Instrucciones de instalacion16 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool WGD9500TC1.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Dryer

AF on my Whirlpool WGD9500TC1

M+

Low inlet air flow detected at install.

From Tech Sheet W10189188, p.40:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (25)

CodeMeaning

AFLow inlet air flow detected at install.F:01Primary control failure.F:02Stuck button or user interface mismatch (appears ONLY in Diagnostic Test Mode).F:20No voltage detected at the heater relay (appears ONLY in Diagnostic Test Mode).F:22Outlet thermistor is open.F:23Outlet thermistor has shorted.F:24Inlet thermistor is open (appears ONLY in Diagnostic Test Mode).F:25Inlet thermistor is shorted (appears ONLY in Diagnostic Test Mode).F:26Motor drive system failure.F:28Moisture sensor strip is open (appears ONLY in Diagnostic Test Mode).F:29Moisture sensor strip has shorted (appears ONLY in Diagnostic Test Mode).F:30Restricted air flow condition exists (appears ONLY in Diagnostic Test Mode).F:31Low voltage condition (less than 30V) detected (appears ONLY in Diagnostic Test…F:50No voltage detected at the water valve relay (appears ONLY in Diagnostic Test…F:70No communication between the machine control and the console electronics.F:71No communication between the machine control and the console electronics.F:72Console electronics failure.F:73Console electronics failure.F:74Console electronics failure.F:75Console electronics failure.F:76Console electronics failure.F:77Console electronics failure.F:78Console electronics failure.L2Low line voltage (less than 30V) detected at installation.PFPower failure occurred while the dryer was running.

Service modes (7)

Customer-Focused Drying Mode Adjustment["In Standby mode (dryer plugged in but not powered up), press and hold the Dryness Level button…
Customer-Focused Drying Mode Adjustment (CF1/CF2/CF3)["In Standby mode (dryer plugged in but not powered up), press and hold the Dryness Level button…
Diagnostic Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…
Inlet Air Flow Diagnostic (Electric Models Only)["Enter Diagnostic Test Mode.","Wait for the 5 second delay and cycle through any saved fault…
Line Voltage Diagnostic["Enter Diagnostic Test Mode.","Wait for the 5 second delay and cycle through any saved fault…
Manual Load Test["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…
Service Diagnostic Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool dryer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass