Model reference
Whirlpool WGD9600TA2
Dryer
12 documents25 error codes9 service modes
Available documentation
Tech Sheet
- Tech Sheet - W10258369 - Rev B16 pg
- TECH SHEET - WP Dryer WGD9600TA012 pg
- Tech Sheet W10258369 Rev B16 pg
- Tech Sheet - do not Discard12 pg
- TECH SHEET - W10198668 - Rev B12 pg
- TECH SHEET - W10143265 - Rev A12 pg
Service Flash
- Dry Time Display Appears to Jump or Stall4 pg
- Service Pointer - 8178790 (Door not Closing)6 pg
Tech Tip
- Instruction Sheet - W10128087- Rev A - Special Handling7 pg
- Instruction Sheet2 pg
- Instruction Sheet12 pg
Installation Guide
- Instrucciones de instalacion16 pg
MyPros+ Max
Diagnose your Whirlpool WGD9600TA2.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (25)
CodeMeaning
AFLow inlet air flow condition detected at install.F:01Primary control failure.F:02Stuck button or user interface mismatchF:20No voltage detected at the heater relayF:22Outlet thermistor is open.F:23Outlet thermistor has shorted.F:24Inlet thermistor is open (appears ONLY in Diagnostic Test Mode).F:25Inlet thermistor is shorted (appears ONLY in Diagnostic Test Mode).F:26Motor drive system failure.F:28Moisture sensor strip is openF:29Moisture sensor strip has shortedF:30Restricted air flow condition exists (appears ONLY in Diagnostic Test Mode).F:31Low voltage condition (less than 30V) detectedF:50No voltage detected at the water valve relay (steam models)F:70No communication between the machine control and the console electronics.F:71No communication between the machine control and the console electronics.F:72Console electronics failure (F:72 through F:78).F:73Console electronics failure (F:72 through F:78).F:74Console electronics failure (F:72 through F:78).F:75Console electronics failure (F:72 through F:78).F:76Console electronics failure (F:72 through F:78).F:77Console electronics failure (F:72 through F:78).F:78Console electronics failure (F:72 through F:78).L2Low line voltage (less than 30V) detected at installation.PFPower failure occurred while the dryer was running.Service modes (9)
- Customer-Focused Drying Mode Adjustment["In Standby mode (dryer plugged in but not powered up), press and hold the Dryness Level button…
- Diagnostic Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…
- Dryness Level Adjust (CF mode)["In Standby mode (dryer plugged in but not powered up), press and hold the Dryness Level button…
- Inlet Air Flow Diagnostic["Enter the Diagnostic Test Mode and wait for the 5 second delay and cycle through any saved fault…
- Inlet Air Flow Diagnostic (Electric Models Only)["Enter Diagnostic Test Mode and wait for 5-second delay.","Cycle through any saved fault…
- Line Voltage Diagnostic["Enter the Diagnostic Test Mode and wait for the 5 second delay and cycle through any saved fault…
- Line Voltage Display["Enter Diagnostic Test Mode.","Wait for the 5 second delay.","Cycle through any saved fault…
- Manual Load Test["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…
- Service Diagnostic Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool dryer models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass