Model reference

Whirlpool WGD97HEXW0

Dryer

10 documents24 error codes3 service modes

Available documentation

Tech Sheet

Tech Sheet - W10436726 - Rev A60 pg
Covers this model
Tech Sheet - W10319757 - Rev B56 pg
Covers this model

Service Flash

Rubber Seal in W10206708 Hose Kit for 'Y' Connector2 pg
Covers this model

Tech Tip

W10349611B1 pg
Covers this model
Instruction Sheet4 pg
Covers this model
Instruction Sheet18 pg
Covers this model
Instruction Sheet - W10609999 - Rev B - Four Way Vent Kit9 pg
Covers this model
Instruction Sheet4 pg
Covers this model
Instruction Sheet2 pg
Covers this model

Installation Guide

Instrucciones de instalacion19 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool WGD97HEXW0.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Dryer

F1E1 on my Whirlpool WGD97HEXW0

M+

Indicates a Cycle Control Unit (CCU)

From Tech Sheet W18242068, p.40:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (24)

CodeMeaning

F1E1Indicates a Cycle Control Unit (CCU) problem.F2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; only…F2E2User Interface Software Error 1 F2E3User Interface Software Error 2 F3E1Exhaust thermistor is open; temperature drops below 18°F (> 50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (< 500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (> 245k ohms).F3E4Inlet thermistor is shorted; temperature above 391°F (< 328 ohms).F3E5Inlet and exhaust thermistor are both open; will occur if P14 connector is not…F3E6Moisture sensor strip is open; only appears in service diagnostic mode.F3E7Moisture sensor strip has shorted; only appears in service diagnostic mode.F4E1No voltage detected at the heater relay; only appears in service diagnostic…F4E3Restricted air flow that may affect dryer performance.F4E4Low L2 voltage (less than 30V) detected at the CCU.F6E1Communication error from UI to CCU F6E2Communication error from CCU to UI FCE0Communication error between ECM and CCU (model WEL98 only).FCE1Communication error from dryer to wireless router (model WEL98 only).FCE2Wireless router cannot communicate with the internet (model WEL98 only).FCE3Antenna A (J2) is bad (model WEL98 only).FCE4Antenna B (J11) is bad (model WEL98 only).FCE5Current Transformer A not functioning at J12 (model WEL98 only).FCE6Current Transformer B not functioning at J12 (model WEL98 only).FCE7Provisioning failure

Service modes (3)

Quick Diagnostic TestFrom Service Diagnostics, navigate to Error Diagnostic > Quick Diagnostic Test
Service Diagnostics1. Ensure dryer is in standby mode (plugged in with all indicators off). 2. Select any three…
UI Component TestFrom Service Diagnostics, navigate to Component Activation > UI Component Test

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool dryer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass