Model reference

Whirlpool YWED9200SQ2

Dryer

5 documents24 error codes6 service modes

Available documentation

Tech Sheet

Tech Sheet - W10258369 - Rev B16 pg
Covers this model
Whirlpool Dryer YWED9200SQ0 Tech Sheet16 pg
Covers this model
Tech Sheet W10258369 Rev B16 pg
Covers this model

Tech Tip

Instruction Sheet - W10128087- Rev A - Special Handling7 pg
Covers this model

Installation Guide

Instrucciones de instalacion16 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool YWED9200SQ2.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Dryer

F:01 on my Whirlpool YWED9200SQ2

M+

Primary control failure.

From Tech Sheet W18446964, p.16:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (24)

CodeMeaning

F:01Primary control failure.F:02Stuck button or user interface mismatch; this fault code will ONLY appear when…F:20No voltage detected at the heater relay F:22Outlet thermistor is open.F:23Outlet thermistor has shorted.F:24Inlet thermistor is open; this fault code will ONLY appear when in the…F:25Inlet thermistor has shorted; this fault code will ONLY appear when in the…F:26Motor drive system failure.F:28Moisture sensor strip is open; this fault code will ONLY appear when in the…F:29Moisture sensor strip has shorted; this fault code will ONLY appear when in the…F:30Restricted airflow condition exists; this fault code will ONLY appear when in…F:31Low voltage condition (less than 30V) detected F:50No voltage detected at the water valve relay (steam models)F:70No communication between the machine control and the console electronics.F:71No communication between the machine control and the console electronics.F:72Console electronics failure (F:72 through F:78).F:73Console electronics failure (F:72 through F:78).F:74Console electronics failure (F:72 through F:78).F:75Console electronics failure (F:72 through F:78).F:76Console electronics failure (F:72 through F:78).F:77Console electronics failure (F:72 through F:78).F:78Console electronics failure (F:72 through F:78).L2Low line voltage (less than 30V) detected at installation.PFPower failure occurred while the dryer was running.

Service modes (6)

Adjusting Customer-Focused Drying Modes (CF1/CF2/CF3)1
Diagnostic Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…
Dryness Level Adjust (CF mode)["In Standby mode (dryer plugged in but not powered up), press and hold the Dryness Level button…
Line Voltage Display["Enter Diagnostic Test Mode.","Wait for the 5 second delay.","Cycle through any saved fault…
Manual Load Test1. Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…
Service Diagnostic Test Mode1. Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool dryer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass