Model reference

Whirlpool RBD275PDQ14

Oven

7 documents24 error codes8 service modes

Available documentation

Tech Sheet

Tech Sheet12 pg
Covers this model
Whirlpool Oven RBD275PDB0 RBD275PDB1 Tech Sheet8 pg
Covers this model

Service Manual

Kitchenaid Whirlpool Built In Single Double Electric Wall Ovens D Models Service Manual146 pg
Covers this model
Service Manual 4317164 bochniak146 pg
Covers this model

Tech Tip

Instruction Sheet1 pg
Covers this model

Installation Guide

Installation Instructions8 pg
Covers this model

Other

servicemanual 4317164.pdf146 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool RBD275PDQ14.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Oven

E3 on my Whirlpool RBD275PDQ14

M+

Wiring harness cavity size select

From Tech Sheet W17006694, p.26:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (24)

CodeMeaning

E3Wiring harness cavity size select jumpers indicate a cavity size different from…F0Default fault code indicating no failure exists; displayed only if user presses…F1Default F-Code F1-E0Electronic control malfunction.F1-E1Key held down too long, or key is shorted.F1-E5Keypad keytail not connected.F1-E6CANCEL key drive line open.F2Keypad is not connected, keypad held too long, or keypad is shorted.F2-E0Temperature sensor opened (R=2875 ohm by spec).F2-E1Temperature sensor shorted (R=825 ohm by spec).F2-E2Oven temp too high F2-E3Oven temp too high F3Wiring harness cavity size does not match the previously stored value (cavity…F3-E0Door is open but latch is locked (door switch is open indicating open door, and…F3-E1Self-clean latch will not lock/unlock.F4Temperature sensor open.F5Temperature sensor shorted or oven temperature is too high (runaway)F5-E0Door is open but latch is locked (door switch open indicating open door, latch…F5-E1Self-clean latch will not lock/unlock.F6Shorted meat probe or miswired temp probe.F7Oven door latch will not lock.F8Oven door is open but latch is locked.F9Oven door latch will not unlock, or common wire (+5Vdc) to latch switch and…PFPower failure indication (not a failure of control).

Service modes (8)

Bake Temperature Offset Adjustment1
Default F code display (no failure)Press and hold CANCEL key for 5 seconds
Fahrenheit to Celsius ConversionPress the BROIL pad for 5 seconds
Fahrenheit to Celsius display changePress the BROIL keypad for 5 seconds
Oven temperature calibrationTouch and hold the BAKE keypad for 5 seconds. The display will indicate the present oven…
Programming the Cavity SizeWithin 60 seconds of power up, press the following touchpads in sequence
Sabbath mode - Double oven1
Sabbath mode - Single oven1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool oven models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass