Model reference

Whirlpool RBS275PVS02

Oven

9 documents26 error codes9 service modes

Available documentation

Tech Sheet

TECH SHEET - Whirlpool Range RBS305PDT1612 pg
Covers this model
TECH SHEET - Whirlpool Oven YRBS305PDQ912 pg
Covers this model

Service Flash

Service Pointer - PF Error Code and/or Slow Running Clock5 pg
Covers this model

Tech Tip

Instruction Sheet1 pg
Covers this model

Installation Guide

Installation Instructions16 pg
Covers this model
Installation Instructions8 pg
Covers this model
Instruction Sheet1 pg
Covers this model
Instruction Sheet1 pg
Covers this model

Other

Rev A_830175812 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool RBS275PVS02.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Oven

F0 on my Whirlpool RBS275PVS02

M+

Default F code - no failure.

From Tech Sheet W12468348, p.40:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (26)

CodeMeaning

F0Default F code F1Electronic control malfunction (applies to all E codes under F1).F1-E0Key held down too long, or key is shorted.F1-E1Keypad keytail not connected.F1-E5CANCEL key drive line open.F1-E6Electronic control malfunction (associated with CANCEL key drive line).F2 E0Key held down too long, or key is shorted.F2 E1Keypad keytail not connected.F2 E5Cancel key drive line open.F2 E6Cancel key drive line open.F2-E0Temperature sensor opened (R=2875 ohms by spec).F2-E1Temperature sensor shorted (R=825 ohms by spec).F2-E2Oven temp too high F2-E3Oven temp too high F3 E0Temperature sensor opened (R=2875 ohms by spec).F3 E1Temperature sensor shorted (R=825 ohms by spec).F3 E2Oven temperature too high, over 575°F (302°C) in Cook mode.F3 E3Oven temperature too high, over 950°F (510°C) in Clean mode.F3-E0Door is open but latch is locked (door switch open indicating open door and…F3-E1Self-clean latch will not lock or will not unlock.F3-E2Oven temp too high F3-E3Oven temp too high F5 E0Door is opened but latch is locked; door switch is open indicating open door…F5 E1Self-Clean latch will not lock/unlock.F5-E0Door is open but latch is locked (condition exists when door switch is open…F5-E1Self-clean latch will not lock or will not unlock.

Service modes (9)

Bake Temperature Offset AdjustmentPress BAKE key for 5 seconds
Cavity Size Programming (Self-Clean Models)Within 60 seconds of power up, press the following keypads in sequence
Cavity Size Programming (Standard-Clean Models)Within 60 seconds of power up, press the following keypads in sequence
Error Code RetrievalPress and hold CANCEL key for 5 seconds.
Fahrenheit to Celsius ConversionPress the BROIL key for 5 seconds
Fahrenheit/Celsius TogglePress and hold BROIL for 5 seconds to toggle temperature between Fahrenheit and Celsius settings.
Programming the Cavity Size (Self-Clean models)Within 60 seconds of power up, press the following keys
Programming the Cavity Size (Standard-Clean models)Within 60 seconds of power up, press the following keys
Verify Cavity Size ProgrammingPress and hold CANCEL key for 5 seconds, then press and hold START key for 5 seconds.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool oven models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass