Model reference

Whirlpool RBS305PDZ2

Oven

7 documents34 error codes9 service modes

Available documentation

Tech Sheet

TECH SHEET8 pg
Covers this model
Whirlpool Oven RBS305PDQ6 Tech Sheet4 pg
Covers this model

Service Manual

Kitchenaid Whirlpool Built In Single Double Electric Wall Ovens D Models Service Manual146 pg
Covers this model
Service Manual 4317164 bochniak146 pg
Covers this model

Installation Guide

Instruction Sheet1 pg
Covers this model
Installation Instructions5 pg
Covers this model

Other

servicemanual 4317164.pdf146 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool RBS305PDZ2.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Oven

F0 on my Whirlpool RBS305PDZ2

M+

Default F code - no failure. Displayed

From Tech Sheet W15333985, p.37:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (34)

CodeMeaning

F0Default F code F1Electronic control malfunction.F1 E0Communications failure or EEPROM checksum failure.F1 E2UL A/D Error(s).F2Keypad is not connected, keypad held too long, or keypad is shorted.F2 E0Shorted key detected.F2 E1Key tail error (membrane tail connection issue).F2-E0Keypad not connected.F2-E2Key held down too long, or key is shorted.F2-E3Key held down too long, or key is shorted.F3Wiring harness cavity size does not match the previously stored value (cavity…F3 E0Oven temperature sensor unplugged or open circuit.F3 E1Oven temperature sensor shorted.F3 E2Bake range over temperature condition.F3 E3Clean range over temperature condition.F3-E0Temperature sensor opened.F3-E1Temperature sensor shorted.F3-E2Oven temperature too high.F3-E3Oven temperature too high.F4Temperature sensor open.F5Temperature sensor shorted or oven temperature is too high (runaway)F5 E0Door and door switches do not agree (door position mismatch).F5 E1Door latch not operating.F5 E2Latch error during clean cycle.F5-E0Door is open, but latch is locked.F5-E1Self-clean latch will not lock.F5-E2Self-clean latch will not unlock.F6Shorted meat probe or miswired temp probe.F6-E0Return line not connected F7Oven door latch will not lock.

View all 34 error codes

F7-E0Common switch wire is defective F8Oven door is open but latch is locked.F9Oven door latch will not unlock, or common wire (+5Vdc) to latch switch and…PFPower failure indication (not a failure of control).

Service modes (9)

Bake Temperature Offset Adjustment1
Fahrenheit to Celsius Conversion1
Fahrenheit to Celsius display changePress the BROIL keypad for 5 seconds
Fault Code DisplayPress and hold CANCEL key for 5 seconds
Oven temperature calibrationTouch and hold the BAKE keypad for 5 seconds. The display will indicate the present oven…
Retrieve last error codePress and hold CANCEL/OFF key for 5 seconds
Sabbath mode - Double oven1
Sabbath mode - Single oven1
Temperature adjustment (calibration)Press and hold BAKE pad for 5 seconds. Current offset (if any) is shown in 3-digit display. CAL is…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool oven models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass