mypros+
Model reference

Whirlpool WTW4800BQ1

Washer

5 documents42 error codes11 service modes

Available documentation

Tech Sheet

  • TechSheet W10677676 RevB44 pg
    Covers this model
  • Diagnostic LED, Diagnostic Test Mode and Error Code summary sheet3 pg
    Covers this model

Service Manual

  • Vertical Modular Washer84 pg
    Covers this model
  • Vertical Modular Washer84 pg
    Covers this model

Installation Guide

  • Instrucciones de instalación10 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool WTW4800BQ1.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (42)

CodeMeaning
F0 E2Over suds condition detectedF0 E4High water temperature during rinse cycleF0 E5Off balance load detected.F0E2Over suds condition detectedF0E4High water temperature detected (105°F or higher) during rinse cycle.F0E5Off balance load detected during operation.F1 E1Main control fault.F1 E2Motor control faultF1E1Main control fault detected.F1E2Motor control faultF2 E1Stuck keyF2 E3Mismatch of main control and UIF2E1Stuck keyF2E3Mismatch of main control and UIF3 E1Pressure sensor faultF3 E2Inlet water temperature faultF3E1Pressure system faultF3E2Inlet water temperature faultF5 E1Lid switch faultF5 E2Lid lock faultF5 E3Lid unlock faultF5 E4Lid not opened between cyclesF5E1Lid switch faultF5E2Lid lock faultF5E3Lid unlock faultF5E4Lid not opened between cyclesF7 E1Basket speed sensor faultF7 E5Shifter faultF7 E6Motor faultF7 E7Motor unable to reach target RPM
View all 42 error codes
F7E1Basket speed faultF7E5Shifter faultF7E6Motor faultF7E7Motor unable to reach target RPMF8 E1No fill / long fillF8 E3Overflow conditionF8 E5Hot and cold water supply hoses are reversed.F8E1No fill / long fillF8E3Overflow conditionF8E5Hot and cold reversedF9 E1Long drainF9E1Long drain

Service modes (11)

  • Automatic Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until the 'Spin' LED is ON (all…
  • Calibration Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse' LED is ON (all…
  • Fault Code Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until the 'Done' LED is ON (all…
  • Manual Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin' and 'Done' LEDs are…
  • Sales Demo Mode["Enter Service Diagnostic Mode.","Turn cycle selector knob until 'Rinse & Done' LEDs are On and…
  • Service Diagnostic Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Service Diagnostic Test ModeRefer to the Service Tech Sheet located inside the unit front top corner for the specific button…
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","Wait 10 seconds after…
  • Software Version Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse', 'Spin', and 'Done'…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Wash' and 'Done' LEDs are…
  • UI Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse' and 'Spin' LEDs are…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass