mypros+
Model reference

Whirlpool WTW4955HW0

Washer

11 documents43 error codes18 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W11447418 - Rev A2 pg
    Covers this model
  • Service Technical Sheet W1074057344 pg
    Covers this model

Service Manual

  • Vertical Modular Washer84 pg
    Covers this model
  • Vertical Modular Washer84 pg
    Covers this model

Service Flash

  • Service Pointer - W11787221 - Rev B - Top-Load Washer Control Board Housing Needs to be Replaced15 pg
    Covers this model
  • Service Pointer - W11648603 - Rev A - Top Load Washers Two-Step Start Behavior Change6 pg
    Covers this model
  • Service Pointer - W11766193 - Rev F - Top Load Washer and Stacked Laundry - F3E1 Pressure Sensor Error or Drain Pump Running Continuously9 pg
    Covers this model
  • Technical Service Pointer12 pg
    Covers this model
  • Technical Service Pointer - Noise During Spin6 pg
    Covers this model
  • Technical Service Pointer - Pressure Dome Port Flash7 pg
    Covers this model

Other

  • Wtw5010lw0 owners-manual-w11436596-reva21 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool WTW4955HW0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (43)

CodeMeaning
F0 E2Over suds condition detectedF0 E4High water temperature during rinse cycleF0 E5Off balance load detected.F0E2Oversuds condition detected.F0E4High water temperature during rinse cycle, spin limited by water temperature.F0E5Off balance load detected.F1 E1Main control fault.F1 E2Motor control faultF1E1Main control fault.F1E2Motor control fault.F2 E1Stuck keyF2 E3Mismatch of main control and UIF2E1Stuck button detected on user interface.F2E3Switch mismatch detected.F3 E1Pressure sensor faultF3 E2Inlet water temperature faultF3E1Pressure system fault.F3E2Inlet water temperature fault.F5 E1Lid switch faultF5 E2Lid lock faultF5 E3Lid unlock faultF5 E4Lid not opened between cyclesF5E1Lid switch fault.F5E2Lid lock faultF5E3Lid unlock faultF5E4Lid not opened between cycles.F7 E1Basket speed sensor faultF7 E5Shifter faultF7 E6Motor faultF7 E7Motor unable to reach target RPM
View all 43 error codes
F7E1Basket speed fault.F7E5Shifter fault.F7E6Motor fault.F7E7Motor unable to reach target RPM.F8 E1No fill / long fillF8 E3Overflow conditionF8 E5Hot and cold water supply hoses are reversed.F8E1Long fill or no fill condition.F8E3Overflow condition detected.F8E5Hot and cold inlet hoses are reversed.F8E6Hot and cold water supply lines are reversed.F9 E1Long drainF9E1Long drain condition.

Service modes (18)

  • AATCC Cycle["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Automatic Test Mode["Enter Service Diagnostic Mode.","Turn cycle selector knob until 'Spin' LED is On and '02' is…
  • Calibration Mode["Enter Service Diagnostic Mode.","Turn cycle selector knob until 'Rinse' LED is On and '04' is…
  • Dry Factory Diagnostics["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Factory Cal Test Cycle["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Factory Diagnostics Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Fault Code Display Mode["Enter Service Diagnostic Mode.","Turn cycle selector knob until 'Done' LED is On and '01' is…
  • Manual Test Mode["Enter Service Diagnostic Mode.","Turn cycle selector knob until 'Spin & Done' LEDs are On and…
  • NVH Cycle["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Sales Demo Mode["Enter Service Diagnostic Mode.","Turn cycle selector knob until 'Rinse & Done' LEDs are On and…
  • Service Diagnostic Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Service Diagnostic Test Modes["After power is applied, wait 10 seconds before activating.","RESET
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off). Wait 10 seconds after…
  • Software Version Display Mode["Enter Service Diagnostic Mode.","Turn cycle selector knob until 'Rinse, Spin, and Done' LEDs are…
  • SW Version Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Tachometer Verification["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Tachometer Verification Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until 'Wash and Done' LEDs are…
  • UI Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass