mypros+
Model reference

Whirlpool WTW4957PW0

Washer

6 documents23 error codes15 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W11654507 - Rev A2 pg
    Covers this model

Service Manual

  • Technical Manual Whirlpool® 3.8 cu ft Top Load Washer with Removable Agitator54 pg
    Covers this model
  • FOR SERVICE TECHNICIAN'S USE ONLY - Technical Manual84 pg
    Covers this model

Service Flash

  • Service Pointer - W11787221 - Rev B - Top-Load Washer Control Board Housing Needs to be Replaced15 pg
    Covers this model
  • Service Pointer - W11766193 - Rev F - Top Load Washer and Stacked Laundry - F3E1 Pressure Sensor Error or Drain Pump Running Continuously9 pg
    Covers this model

Quick Reference

  • Quick Start Guide2 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool WTW4957PW0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (23)

CodeMeaning
F0E0No FaultF0E2OversudsF0E4High Water TemperatureF0E5Off Balance LoadF1E1Main Control FaultF1E2Motor Control FaultF2E1Stuck ButtonF2E3Switch MismatchF3E1Pressure System FaultF3E2Inlet Water Temperature FaultF5E1Lid Switch FaultF5E2Lid Lock FaultF5E3Lid Unlock FaultF5E4Lid Not Opened Between CyclesF7E1Basket Speed FaultF7E5Shifter FaultF7E6Motor FaultF7E7Motor Unable to Reach Target RPMF8E1Long Fill / No FillF8E3Overflow ConditionF8E5Hot and cold inlet hoses are reversed.F8E6Hot, Cold ReversedF9E1Long Drain

Service modes (15)

  • Automatic Test Mode["Enter Service Diagnostic Mode.","Rotate cycle selector knob until status LEDs match the Automatic…
  • Calibration Mode["Enter Service Diagnostic Mode.","Rotate cycle selector knob until status LEDs match the…
  • Dry Factory Diagnostics["Enter Service Diagnostic Mode.","Rotate cycle selector knob until status LEDs match the Dry…
  • Factory Cal Test Cycle["Enter Service Diagnostic Mode.","Rotate cycle selector knob until status LEDs match the Factory…
  • Factory Diagnostics Mode["Enter Service Diagnostic Mode.","Rotate cycle selector knob until status LEDs match the Factory…
  • Fault Code Display Mode["Enter Service Diagnostic Mode.","Rotate cycle selector knob until status LEDs match the Fault…
  • Manual Test Mode["Enter Service Diagnostic Mode.","Rotate cycle selector knob until status LEDs match the Manual…
  • Sales Demo Mode["Enter Service Diagnostic Mode.","Rotate cycle selector knob until status LEDs match the Sales…
  • Service Diagnostic Mode Entry["Wait 10 seconds after power is applied before activating.","RESET
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off). Wait 10 seconds after…
  • Software Version Display Mode["Enter Service Diagnostic Test Modes (see entry steps 1-2).","Turn cycle selector knob until…
  • SW Version Display Mode["Enter Service Diagnostic Mode.","Rotate cycle selector knob until status LEDs match the SW…
  • Tachometer Verification["Enter Service Diagnostic Mode.","Rotate cycle selector knob until status LEDs match the…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes (see entry steps 1-2).","Turn cycle selector knob until Wash…
  • UI Test Mode["Enter Service Diagnostic Mode.","Rotate cycle selector knob until status LEDs match the UI Test…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass