mypros+
Error code reference

ASKO Dryer Error Code F5

Maximum permitted programme time exceeded-the machine stops after 3 hours

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F5 error code actually means

The F5 error means your Asko dryer ran for 3 hours without finishing its cycle, so it stopped itself as a safety measure. This usually happens because the laundry was too wet going in, or because something is blocking the dryer from working efficiently. Try spinning your clothes at a higher speed before drying and make sure the dryer's air vents are clear.

Diagnostic procedure

The full F5 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check if the customer has tried spinning at a higher speed. Check if the machine was switched off for 30 minutes before restarting. Ensure external air has free passage. Replace thermistor or control unit if defective.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F5 procedure $9.95

Or subscribe: $29/month for all codes plus Max AI diagnostics, with 70 Max messages a day.

Most common causes of F5

Ranked by how often they cause this code
  1. 1Laundry spun at too low a speed
  2. 2Blocked external air passages
  3. 3Control unit not fully reset
  4. 4Defective thermistor
  5. 5Defective control unit

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F5

What does F5 mean on a Asko dryer?
F5 on an Asko dryer means the maximum allowed programme time of 3 hours has been exceeded and the machine has stopped itself. The dryer was unable to complete its drying cycle within the time limit, which points to a condition that is slowing down drying efficiency. Common triggers include overly wet laundry, blocked air passages, a faulty thermistor, or a control unit that needs a full reset.
Is it safe to keep using my Asko dryer when F5 is showing?
The dryer stops automatically when F5 is triggered, so it is not actively running while the error is displayed. You should not attempt to repeatedly restart the machine without investigating the underlying cause, as persistent extended cycle times can indicate a component fault that may worsen over time. Resolve the issue before returning the dryer to normal use.
How much does it cost to repair an Asko dryer showing F5?
If the fix is something you can do yourself, such as clearing a blocked air vent or adjusting the spin speed on your washer, there is no parts cost involved. Thermistor replacement is generally an affordable repair, typically in the range of $20 to $80 for the part plus any labor costs. Control unit replacement is more involved and can range from $150 to $400 or more depending on parts availability and the technician's rates.
Can I fix the F5 error myself without calling a technician?
In many cases, yes. Start by switching the dryer off and leaving it unpowered for at least 30 minutes to allow the control unit to fully reset. Then check that the external air passages are unobstructed, and make sure future loads have been spun at 800 rpm or higher before drying. If the error returns after these steps, a defective thermistor or control unit is likely involved and professional diagnosis is recommended.
Will resetting the dryer clear the F5 error code?
A full power-off reset, with the machine switched off for at least 30 minutes, may clear the F5 error if the root cause was a temporary condition such as an exceptionally wet load or a control unit that did not complete its previous reset. However, if the underlying problem is a blocked air path, defective thermistor, or faulty control unit, the error will return after the next cycle reaches the 3-hour limit.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass