mypros+
Error code reference

Bosch Dishwasher Error Code Not Heating

Water temperature rose less than 9°F in 15 minutes during wash cycle.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Not Heating error code actually means

Your Bosch dishwasher is detecting that the water inside is not getting warm enough during the wash cycle. This usually means the heating element or a related electrical component has failed. Dishes may come out dirty, cold, or not fully sanitized when this error is active.

Diagnostic procedure

The full Not Heating procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
Confirm the fault
Power cycle the unit: switch off the breaker for 60 seconds, then restore power. If the code returns, the fault is persistent and the procedure below isolates the cause.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Not Heating procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of Not Heating

Ranked by how often they cause this code
  1. 1Failed Heating Element
  2. 2Faulty NTC Temperature Sensor
  3. 3Defective Control Board Relay
  4. 4Damaged Wiring or Loose Connections
  5. 5Low Inlet Water Temperature

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Not Heating

What does Not Heating mean on a Bosch dishwasher?
This error means the dishwasher's control system detected that water temperature rose less than 9°F over a 15-minute period during the wash cycle. The dishwasher monitors temperature via a sensor and expects the heating element to raise water temperature at a minimum rate. When that rate is not met, the fault is logged. Common causes include a failed heating element, a faulty temperature sensor, or a defective control board relay.
Is it safe to keep using my Bosch dishwasher when the Not Heating error is active?
Running the dishwasher with this error active is generally not dangerous, but cleaning performance will be significantly reduced because water is not reaching proper wash temperatures. Sanitization cycles will not be effective, and grease and bacteria may not be fully removed from dishes. It is best to resolve the fault before relying on the appliance for regular use.
Will resetting my Bosch dishwasher clear the Not Heating error?
A reset may temporarily clear the error from the display, but if the underlying component has failed, the fault will return as soon as the dishwasher attempts to heat water again during the next cycle. Resetting is useful for ruling out a one-time control glitch but should not be considered a fix. A proper diagnosis of the heating element, temperature sensor, and associated wiring is needed to resolve the error permanently.
Can I fix the Not Heating error on my Bosch dishwasher myself?
Some steps, such as inspecting wiring connections or running the hot water before a cycle to raise inlet temperature, can be done without special tools. Replacing the heating element or NTC temperature sensor requires basic electrical safety knowledge, a multimeter, and the ability to access the dishwasher's interior components. Control board replacement is more complex and may be better handled by a qualified technician.
How much does it cost to repair a Bosch dishwasher with a Not Heating error?
Repair costs vary depending on the failed component. A replacement heating element typically ranges from $30 to $80 for the part alone, while an NTC temperature sensor is generally $15 to $40. Control board replacement is the most expensive scenario, with parts alone often ranging from $100 to $250 or more. Adding labor costs for a professional technician will increase the total, generally by $75 to $150 depending on your region.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass