mypros+
Error code reference

Bosch Dishwasher Error Code Open or short circuit Door thermistor (Normal/Normal)

Temperature sensed was below 32°F or above 210°F on the door thermistor.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Open or short circuit Door thermistor (Normal/Normal) error code actually means

Your Bosch dishwasher detected a problem with a temperature sensor located in the door, and the reading it got was so far outside the normal range that the appliance flagged it as a malfunction. This usually means the sensor or its wiring has failed rather than an actual extreme temperature inside the machine. The dishwasher will not operate normally until this sensor issue is resolved.

Diagnostic procedure

The full Open or short circuit Door thermistor (Normal/Normal) procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
Confirm the fault
Power cycle the unit: switch off the breaker for 60 seconds, then restore power. If the code returns, the fault is persistent and the procedure below isolates the cause.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Open or short circuit Door thermistor (Normal/Normal) procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of Open or short circuit Door thermistor (Normal/Normal)

Ranked by how often they cause this code
  1. 1Failed door thermistor
  2. 2Damaged wiring in the door hinge area
  3. 3Corroded or loose connector pins
  4. 4Moisture intrusion into the connector
  5. 5Faulty control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Open or short circuit Door thermistor (Normal/Normal)

What does Open or short circuit Door thermistor (Normal/Normal) mean on a Bosch dishwasher?
This error code means the control board detected a temperature reading from the door thermistor that fell below 32°F or above 210°F, which are outside the boundaries of a valid signal. Rather than reflecting actual extreme temperatures, these out-of-range readings indicate that the thermistor circuit has an open break or a short circuit. The dishwasher flags this condition to prevent operating with unreliable temperature data.
Is it safe to use my Bosch dishwasher when the door thermistor error is active?
Running the dishwasher with an active door thermistor fault is not recommended. The control board relies on temperature sensor data to manage heating and drying cycle timing, and operating without a valid sensor reading can result in improper cycle behavior. It is best to resolve the fault before running additional cycles.
Will resetting my Bosch dishwasher clear the door thermistor error code?
A power reset by unplugging the dishwasher or switching off the circuit breaker for a few minutes may temporarily clear the error code, but it will return if the underlying fault in the thermistor or its wiring has not been corrected. A reset is useful for confirming whether the fault is intermittent, but it is not a permanent fix. The thermistor circuit needs to be inspected and repaired to resolve the code reliably.
Can I fix the door thermistor error on my Bosch dishwasher myself?
A knowledgeable DIYer can diagnose this fault by visually inspecting the door wiring harness for visible damage, checking that the thermistor connector is clean and fully seated, and testing the thermistor resistance with a multimeter. If the sensor itself is faulty, replacing it requires disassembling part of the door panel, which is manageable with basic tools and the correct replacement part. Wiring repairs in the hinge area may require soldering or connector replacement and are more involved.
How much does it cost to repair a door thermistor fault on a Bosch dishwasher?
If the thermistor sensor itself needs replacement, parts typically range from around $15 to $50 depending on the specific model. If a professional technician is needed for diagnosis and replacement, total repair costs including labor generally range from $100 to $250. Control board replacement, if required as a last resort, would cost significantly more.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass