mypros+
Error code reference

Cove Dishwasher Error Code 050127

Wash pump drive system

Cove codesCove dishwasher codes

Wash pump drive system: IPM overcurrent shunt error.

First step from the service manual

Replace the MCM assembly.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 050127.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 050127 means on a Cove dishwasher

Error code 050127 on a Cove dishwasher indicates a fault within the wash pump drive system, specifically an IPM (Intelligent Power Module) overcurrent shunt error. The IPM is the power electronics component inside the Motor Control Module (MCM) responsible for driving the wash pump motor. A shunt resistor within the IPM circuit monitors current flow to detect abnormal conditions. When current exceeds the safe threshold detected by this shunt, the control system triggers this fault to protect the motor and electronics from damage.

This error typically points to a failure within the MCM assembly itself rather than an external wiring or pump issue. The IPM can fail due to internal short circuits, degraded power transistors, or a faulty shunt resistor that produces inaccurate overcurrent readings. In some cases, a seized or heavily loaded wash pump motor can draw excessive current and trigger the shunt protection, but the diagnostic path leads directly to the MCM assembly as the primary suspect.

Because the overcurrent detection circuitry is integrated within the MCM, this fault is not field-repairable at the component level. The entire MCM assembly must be replaced to restore proper wash pump operation. Before replacement, a technician should verify there are no obvious obstructions in the pump or signs of a failed pump motor that could cause excessive load, as these conditions could damage a new MCM if left unaddressed.

Source: manufacturer service documentation.

Common causes of 050127

  1. 01

    Failed MCM Assembly (IPM Internal Fault)

    Part replacement

    The Intelligent Power Module within the MCM assembly has developed an internal short circuit or a failed shunt resistor, causing false or real overcurrent detection. This is the most common cause and the primary repair target for this error code.

  2. 02

    Seized or Mechanically Blocked Wash Pump

    Wiring / connection

    A wash pump motor that is seized or obstructed by debris forces the IPM to supply excessive current to overcome resistance, triggering the overcurrent shunt. Inspect the pump impeller for blockages before installing a replacement MCM.

  3. 03

    Wash Pump Motor Winding Failure

    Part replacement

    A shorted winding in the wash pump motor can draw abnormally high current through the IPM drive circuit, tripping the overcurrent shunt. Resistance testing of the motor windings can help confirm this condition.

  4. 04

    Wiring Harness Short Between MCM and Pump

    Wiring / connection

    Damaged or chafed wiring between the MCM assembly and the wash pump motor can create a short circuit that mimics an overcurrent condition. Inspect the harness for pinches, burns, or insulation damage near routing points.

See the test procedure for each cause

Frequently asked questions about 050127

What does 050127 mean on a Cove dishwasher?
Error code 050127 indicates a wash pump drive system IPM overcurrent shunt error. The Intelligent Power Module inside the Motor Control Module detected an overcurrent condition in the circuit driving the wash pump. This is an internal electronics fault that requires replacement of the MCM assembly to resolve.
Can I fix error code 050127 myself on a Cove dishwasher?
The repair requires replacing the MCM assembly, which involves working with high-voltage components and precise reassembly. Knowledgeable DIYers comfortable with appliance repair may be able to complete this, but the job is generally recommended for a qualified technician. Before replacing the MCM, also check for any pump blockages that could overload a new module.
Is it safe to use my Cove dishwasher while error 050127 is active?
No, the dishwasher should not be operated while this error is present. The fault indicates a potentially serious overcurrent condition in the wash pump drive circuit, and continued operation could cause further damage to the MCM, the wash pump motor, or related wiring. Disconnect power to the unit until the repair is completed.
Will resetting my Cove dishwasher clear error code 050127?
A power reset may temporarily clear the error display, but the underlying fault in the MCM assembly or wash pump system will cause the code to return once the dishwasher attempts to run a wash cycle. A reset alone is not a repair and does not address the overcurrent condition causing the fault.
How much does it cost to repair error code 050127 on a Cove dishwasher?
Repair costs will vary depending on parts pricing and labor rates in your area. The primary repair is replacement of the MCM assembly, which is a premium component in a high-end appliance, and parts costs alone can be significant. Total repair costs including labor typically range from a few hundred dollars to over five hundred dollars depending on your location and service provider.

Related Cove dishwasher codes

All Cove dishwasher codes
View all 62 Cove dishwasher codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass