mypros+
Error code reference

Cove Dishwasher Error Code 050180

Wash pump drive system

Cove codesCove dishwasher codes

Wash pump drive system: SV transmission error. Board-level communication error where wash pump has not received a speed setpoint from MCM for 80 ms.

First step from the service manual

Use the Options menu to do a 'Reset All,' and set the Connect? option back to where it was before the reset.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 050180.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 050180 means on a Cove dishwasher

Error code 050180 on a Cove dishwasher indicates a wash pump drive system SV transmission error. Specifically, this is a board-level communication fault where the wash pump motor controller has not received a speed setpoint signal from the Main Control Module (MCM) within an 80-millisecond window. The MCM is responsible for continuously sending speed commands to the wash pump drive system, and when that communication is interrupted or delayed beyond the 80 ms threshold, the dishwasher halts operation and logs this fault code to protect the wash pump from operating in an uncontrolled state.

This error is rooted in the communication pathway between the MCM and the wash pump drive board, rather than a mechanical failure of the pump itself. Possible causes include a corrupted control board configuration, a loose or damaged wiring harness connector between the MCM and the pump drive, or a firmware or software state that has caused the MCM to stop transmitting setpoint data. Because the threshold is extremely tight at 80 ms, even a brief signal interruption is enough to trigger this fault.

The first recommended diagnostic step is a full 'Reset All' performed through the Options menu on the control panel. This resets the MCM configuration to factory defaults and clears any corrupted communication states. After completing the reset, the Connect option must be restored to its previous setting before resuming normal operation. If the error returns after the reset, further inspection of the wiring harness and control board connections is warranted.

Source: manufacturer service documentation.

Common causes of 050180

  1. 01

    MCM configuration or software fault

    Wiring / connection

    A corrupted or unstable software state in the Main Control Module can cause it to stop transmitting speed setpoints to the wash pump drive. A 'Reset All' via the Options menu is designed to clear this condition.

  2. 02

    Loose or disconnected wiring harness connector

    Wiring / connection

    A loose, corroded, or partially disconnected connector in the communication harness between the MCM and the wash pump drive board can interrupt the signal. Inspect all related connectors for secure seating and signs of corrosion or damage.

  3. 03

    Damaged communication wiring

    Part replacement

    Physical damage to the wiring between the MCM and the wash pump drive, such as chafing, pinching, or moisture intrusion, can cause intermittent or complete signal loss. A visual inspection of the harness routing should be performed.

  4. 04

    Faulty wash pump drive board

    Part replacement

    If the pump drive board has failed internally, it may not be able to receive or acknowledge communication from the MCM, triggering this fault. This is typically confirmed after wiring and MCM resets have been ruled out.

  5. 05

    Failed Main Control Module (MCM)

    Part replacement

    A failing or failed MCM may be unable to generate and transmit the required speed setpoint signals to the pump drive. This is considered less common but should be evaluated if all other causes have been eliminated.

See the test procedure for each cause

Frequently asked questions about 050180

What does 050180 mean on a Cove dishwasher?
Error code 050180 indicates a wash pump drive system SV transmission error. The Main Control Module (MCM) failed to send a speed setpoint signal to the wash pump within an 80-millisecond window, causing the dishwasher to stop operation. This is a board-level communication fault between the MCM and the wash pump drive system. It does not necessarily mean the wash pump itself has failed.
Will resetting the dishwasher clear error code 050180?
A full 'Reset All' through the Options menu is the first recommended step and can resolve this error if it was caused by a corrupted software state or temporary communication glitch. After performing the reset, you must restore the Connect option to its previous setting before restarting the dishwasher. If the error returns after the reset, a deeper inspection of the wiring and control boards is necessary.
Is it safe to use my Cove dishwasher when error code 050180 appears?
The dishwasher will typically halt operation when this fault is active, preventing a wash cycle from running without proper pump control. You should not attempt to bypass or force-run the dishwasher while this error is present. Perform the recommended reset first, and if the error persists, have the unit inspected by a qualified technician before continued use.
How do I fix error code 050180 on my Cove dishwasher?
Start by using the Options menu to perform a 'Reset All,' then restore the Connect setting to where it was before the reset. If the error clears, run a normal cycle to confirm the repair. If the fault returns, check the wiring harness between the MCM and the wash pump drive board for loose connectors or damage, and consider having the control boards evaluated by a technician.
How much does it cost to repair a Cove dishwasher showing error code 050180?
If the reset resolves the issue, there is no parts cost involved. If wiring repairs are needed, costs can range from modest labor fees up to several hundred dollars depending on the extent of the damage. Replacement of a wash pump drive board or Main Control Module typically falls in the range of a few hundred to several hundred dollars including parts and labor. Costs vary based on region and service provider.

Related Cove dishwasher codes

All Cove dishwasher codes
View all 62 Cove dishwasher codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass